FRONT DOOR LOCK > INSPECTION

for Preparation Click here



1. INSPECT FRONT DOOR LOCK ASSEMBLY LH (W/O DOUBLE LOCK SYSTEM)


    B065427E03

  1. Apply battery voltage to the door lock and check operation of the motor.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    		Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    		Unlock

    HINT:
    If the result is not as specified, replace the door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Door Lock Position
    		Specified Condition
    7 - 8
    		Lock
    		10 kΩ or higher
    7 - 8
    		Unlock
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.



    B065428E02

  1. Driver side only:
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    7 - 9
    		ON (Door lock set to LOCK)
    		Below 1 Ω
    7 - 9, 7 - 10
    		OFF (Free)
    		10 kΩ or higher
    7 - 10
    		ON (Door lock set to UNLOCK)
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.



2. INSPECT FRONT DOOR LOCK ASSEMBLY RH (W/O DOUBLE LOCK SYSTEM)


    B065429E02

  1. Apply battery voltage to the door lock and check operation of the motor.

    Standard:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    		Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    		Unlock

    HINT:
    If the result is not as specified, replace the door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Door Lock Position
    		Specified Condition
    7 - 8
    		Lock
    		10 kΩ or higher
    7 - 8
    		Unlock
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.



    B065430E03

  1. Driver side only:
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    6 - 8
    		ON (Door lock set to LOCK)
    		Below 1 Ω
    5 - 8, 6 - 8
    		OFF (Free)
    		10 kΩ or higher
    5 - 8
    		ON (Door lock set to UNLOCK)
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.



3. INSPECT FRONT DOOR LOCK ASSEMBLY LH (W/ DOUBLE LOCK SYSTEM)


    B069901E01

  1. Apply battery voltage to the door lock and check operation of the motor.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 3
    		Lock
    Battery positive (+) → Terminal 3
    Battery negative (-) → Terminal 4
    		Unlock

    HINT:
    If the result is not as specified, replace the door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Door Lock Position
    		Specified Condition
    5 - 8, 7 - 8
    		Lock
    		10 kΩ or higher
    5 - 8, 7 - 8
    		Unlock
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.



    B069902E01

  1. Driver side only:
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    5 - 9, 7 - 9
    		ON (Door lock set to LOCK)
    		Below 1 Ω
    5 - 9, 7 - 9
    7 - 9, 7 - 10
    		OFF (Free)
    		10 kΩ or higher
    5 - 10, 7 - 10
    		ON (Door lock set to UNLOCK)
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.

  1. Check operation of the double lock motor.

    1. Apply battery voltage and set the door lock motor to the lock position.

    2. Apply battery voltage to the door lock and check operation of the double lock motor.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      		Double Locking System is set
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      		Double Locking System is unset

      HINT:
      If the result is not as specified, replace the door lock assembly.

    3. Check that the doors cannot be unlocked by operating the control cable while the double locking system is set.

      HINT:
      If the result is not as specified, replace the door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Door Lock Position
    		Specified Condition
    5 - 6
    		Set
    		Below 1 Ω
    5 - 6
    		Unset
    		10 kΩ or higher

    HINT:
    If the result is not as specified, replace the door lock assembly.



4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (W/ DOUBLE LOCK SYSTEM)


    B064708E01

  1. Apply battery voltage to the door lock and check operation of the motor.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1
    		Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    		Unlock

    HINT:
    If the result is not as specified, replace the door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Door Lock Position
    		Specified Condition
    7 - 8, 7 - 10
    		Lock
    		10 kΩ or higher
    7 - 8, 7 - 10
    		Unlock
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.



    B064720E01

  1. Driver side only:
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    6 - 8, 6 - 10
    		ON (Door lock set to LOCK)
    		Below 1 Ω
    6 - 8, 6 - 10
    5 - 8, 5 - 10
    		OFF (Free)
    		10 kΩ or higher
    5 - 8, 5 - 10
    		ON (Door lock set to UNLOCK)
    		Below 1 Ω

    HINT:
    If the result is not as specified, replace the door lock assembly.

  1. Check operation of the double lock motor.

    1. Apply battery voltage and set the door lock motor to the lock position.

    2. Apply battery voltage to the door lock and check operation of the double lock motor.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      		Double Locking System is set
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      		Double Locking System is unset

      HINT:
      If the result is not as specified, replace the door lock assembly.

    3. Check that the doors cannot be unlocked by operating the control cable while the double locking system is set.

      HINT:
      If the result is not as specified, replace the door lock assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Door Lock Position
    		Specified Condition
    9 - 10
    		Set
    		Below 1 Ω
    9 - 10
    		Unset
    		10 kΩ or higher

    HINT:
    If the result is not as specified, replace the door lock assembly.