OUTER REAR VIEW MIRROR > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (W/ MEMORY)


    B069418E04

  1. Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 1 (RMVR)
      Battery negative (-) → Terminal 10 (RM+R)
      		Turns upward (A)
      Battery positive (+) → Terminal 10 (RM+R)
      Battery negative (-) → Terminal 1 (RMVR)
      		Turns downward (B)
      Battery positive (+) → Terminal 9 (RMHR)
      Battery negative (-) → Terminal 10 (RM+R)
      		Turns left (C)
      Battery positive (+) → Terminal 10 (RM+R)
      Battery negative (-) → Terminal 9 (RMHR)
      		Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 4 (HTR+)
      Battery negative (-) → Terminal 12 (HTR-)
      		Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		Moves to retracted position and then stops
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 3 (MR)
      		Moves to driving position and then stops



    B069691E01

  1. Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 7 (EC+)
      Battery negative (-) → Terminal 15 (EC-)
      		Mirror surface changes to dark



2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (W/O MEMORY)


    B069699E01

  1. Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      		Turns upward (A)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      		Turns downward (B)
      Battery positive (+) → Terminal 4(MH)
      Battery negative (-) → Terminal 5 (M+)
      		Turns left (C)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      		Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 1 (HTR+)
      Battery negative (-) → Terminal 7 (HTR-)
      		Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 10 (MR)
      		Moves to retracted position and then stops
      Battery positive (+) → Terminal 10 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		Moves to driving position and then stops



    B069719E01

  1. Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 2 (EC+)
      Battery negative (-) → Terminal 8 (EC-)
      		Mirror surface changes to dark



3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (W/ MEMORY)


    B069417E04

  1. Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 1 (LMVR)
      Battery negative (-) → Terminal 10 (LM+R)
      		Turns upward (A)
      Battery positive (+) → Terminal 10 (LM+R)
      Battery negative (-) → Terminal 1 (LMVR)
      		Turns downward (B)
      Battery positive (+) → Terminal 9 (LMHR)
      Battery negative (-) → Terminal 10 (LM+R)
      		Turns left (C)
      Battery positive (+) → Terminal 10 (LM+R)
      Battery negative (-) → Terminal 9 (LMHR)
      		Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 4 (HTR+)
      Battery negative (-) → Terminal 12 (HTR-)
      		Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		Moves to retracted position and then stops
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 3 (MR)
      		Moves to driving position and then stops



    B069692E01

  1. Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 7 (EC+)
      Battery negative (-) → Terminal 15 (EC-)
      		Mirror surface changes to dark



4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (W/O MEMORY)


    B069698E01

  1. Inspect outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      		Turns upward (A)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      		Turns downward (B)
      Battery positive (+) → Terminal 4 (MH)
      Battery negative (-) → Terminal 5 (M+)
      		Turns left (C)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      		Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 1 (HTR+)
      Battery negative (-) → Terminal 7 (HTR-)
      		Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 10 (MR)
      		Moves to retracted position and then stops
      Battery positive (+) → Terminal 10 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		Moves to driving position and then stops



    B069718E01

  1. Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → Terminal 4 (EC+)
      Battery negative (-) → Terminal 5 (EC-)
      		Mirror surface changes to dark