TELEVISION CAMERA ECU > INSTALLATION

for Preparation Click here



1. INSTALL TELEVISION CAMERA ECU


    E111289

  1. Install the television camera ECU with the 3 bolts.

  1. Connect the 3 connectors.



2. INSTALL ROOF SIDE GARNISH ASSEMBLY INNER RH


    B111796

  1. Engage the 7 clips and install the roof side garnish assembly inner.



    B111795

  1. Install the 3 clips.

  1. Install the 3 bolts and tonneau cover holder cap.



    B111797

  1. Engage the 4 claws and install the seat belt bezel.



3. INSTALL NO.1 TONNEAU COVER HOLDER CAP


4. INSTALL NO.2 ROOM LIGHT ASSEMBLY


    B111794

  1. Connect the connector.

  1. Engage the claw and install the room light assembly No.2.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    B111793

  1. Engage the 2 clips and install the deck trim side panel assembly.

  1. Install the 4 clips.



6. INSTALL ROPE HOOK

  1. Install the 2 rope hooks with the 2 bolts.

    Torque:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure to install the other side.



7. INSTALL REAR SEAT SIDE COVER RH


    B111791

  1. Engage the 4 clips and install the rear seat side cover.

  1. Install the 3 clips.



8. INSTALL REAR NO.1 SEAT BELT ASSEMBLY OUTER RH

  1. Install the rear No.1 seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



9. INSTALL DECK SIDE TRIM COVER RH


    B111808

  1. Engage the 5 claws and install the deck side trim cover.



10. INSTALL REAR DOOR SCUFF PLATE RH


    B111783

  1. Connect the connector. (w/ illumination scuff plate)

  1. Engage the 4 claws and 2 clips, and install the rear door scuff plate.



11. INSTALL REAR FLOOR FINISH SIDE PLATE RH


    B111792

  1. Engage the 2 clips and install the rear floor finish side plate.

  1. Install the clip.



12. INSTALL REAR FLOOR FINISH PLATE


    B110477

  1. Engage the 2 claws and 6 clips, and install the rear floor finish plate.

  1. Install the 2 clips.



13. INSTALL DECK SIDE TRIM BOX LH


    B111781

  1. Install the deck side trim box with the 2 clips.



14. INSTALL DECK SIDE TRIM BOX RH


15. INSTALL JACK CARRIER ASSEMBLY

  1. Install the jack carrier assembly, jack assembly and jack carrier support.



16. INSTALL BACK DOOR WEATHERSTRIP


17. INSTALL NO.3 DECK BOARD SUB-ASSEMBLY


    B110025

  1. Install the deck No.3 board sub-assembly with the 2 bolts and 2 nuts.



18. INSTALL NO.2 DECK BOARD SUB-ASSEMBLY


    B110024

  1. Install the deck No.2 board sub-assembly with the 4 bolts and 2 nuts.



19. INSTALL DECK FLOOR BOX REAR


    B110023

  1. Install the deck floor box rear with the 2 clips.



20. INSTALL DECK FLOOR BOX FRONT


    B110022

  1. Install the deck floor box front with the 2 clips.



21. INSTALL DECK BOARD SUB-ASSEMBLY


    B110455

  1. Install the deck board sub-assembly with the 2 bolt.

  1. Engage the 5 clips.



22. INSTALL TONNEAU COVER ASSEMBLY


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


24. ADJUST TELEVISION CAMERA AIMING
(Click here)


25. ADJUST STEERING ANGLE NEUTRAL POINT
(Click here)


26. ADJUST MAXIMUM STEERING ANGLE
(Click here)


27. PERFORM INITIALIZATION

NOTICE:
Some systems need initialization when disconnecting the cable from the negative battery terminal. (Click here)