TELEVISION CAMERA ECU > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE TONNEAU COVER ASSEMBLY


3. REMOVE DECK BOARD SUB-ASSEMBLY


    B110021

  1. Disengage the 5 clips and turn up the front side of the deck board.

  1. Remove the 2 bolts and deck board sub-assembly.



4. REMOVE DECK FLOOR BOX FRONT


    B110022

  1. Using a clip remover, remove the 2 clips and deck floor box front.



5. REMOVE DECK FLOOR BOX REAR


    B110023

  1. Using a clip remover, remove the 2 clips and deck floor box rear.



6. REMOVE NO.3 DECK BOARD SUB-ASSEMBLY


    B110025

  1. Remove the 2 bolts, 2 nuts and deck No.3 board sub-assembly.



7. REMOVE NO.2 DECK BOARD SUB-ASSEMBLY


    B110024

  1. Remove the 4 blots, 2 nuts and deck No.2 board sub-assembly.



8. REMOVE BACK DOOR WEATHERSTRIP


9. REMOVE JACK CARRIER ASSEMBLY

  1. Remove the jack carrier support, jack assembly and jack carrier assembly.



10. REMOVE DECK SIDE TRIM BOX LH


    B111781E01

  1. Remove the clip (A).

  1. Using a clip remover, remove the clip (B) and deck side trim box.



11. REMOVE DECK SIDE TRIM BOX RH


12. REMOVE REAR FLOOR FINISH PLATE


    B111780

  1. Using a clip remover, remove the 2 clips.

  1. Disengage the 2 claws and 6 clips, and remove the rear floor finish plate.



13. REMOVE REAR FLOOR FINISH SIDE PLATE RH


    B111792

  1. Using a clip remover, remove the clip.

  1. Disengage the 2 clips and remove the rear floor finish side plate.



14. REMOVE REAR DOOR SCUFF PLATE RH


    B111783

  1. Disengage the 4 claws and 2 clips, and remove the rear door scuff plate.

  1. Disconnect the connector. (w/ illumination scuff plate)



15. REMOVE DECK SIDE TRIM COVER RH


    B111790E01

  1. Using a moulding remover, disengage 3 claws (A).

  1. Disengage 2 claws (B) and remove the deck side trim cover by pulling it to inside the vehicle.



16. SEPARATE REAR NO.1 SEAT BELT ASSEMBLY OUTER RH

  1. Remove the bolt and separate the rear No.1 seat outer belt assembly.



17. REMOVE REAR SEAT SIDE COVER RH


    B111791

  1. Using a clip remover, remove the 3 clips.

  1. Disengage the 4 clips and remove the rear seat side cover.



18. REMOVE ROPE HOOK

  1. Remove the 2 bolts and 2 rope hooks.

    HINT:
    Use the same procedure to remove the other side.



19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    B111793

  1. Using a clip remover, remove the 4 clips.

  1. Disengage the 2 clips and remove the deck trim side panel assembly.



20. REMOVE NO.2 ROOM LIGHT ASSEMBLY


    B111794

  1. Using a screwdriver, disengage the claw and remove the room light assembly No.2.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connector.



21. REMOVE NO.1 TONNEAU COVER HOLDER CAP


22. REMOVE ROOF SIDE GARNISH ASSEMBLY INNER RH


    B111795

  1. Using a screwdriver, remove the tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 3 bolts.

  1. Using a clip remover, remove the 3 clips.



    B111796

  1. Disengage the 7 clips and remove the roof side garnish assembly inner.



    B111797

  1. Disengage the 4 claws and separate the seat belt bezel.



23. REMOVE TELEVISION CAMERA ECU


    E111289

  1. Disconnect the 3 connectors.

  1. Remove the 3 bolts and the television camera ECU.