DTC    P0AA1-226    Hybrid Battery Positive Contactor Circuit Stuck Closed

DTC    P0AA2-227    Hybrid Battery Positive Contactor Circuit Stuck Open

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0AA1-224. (Click here)

DTCNo.
INF Code
DTC Detection Condition
Trouble Area
P0AA1
226
Open or +B short in SMR2 (CON2) circuit
  1. Wire harness or connector
  2. HV relay assembly
  3. HV control ECU
P0AA2
227
GND short in SMR2 (CON2) circuit
  1. Wire harness or connector
  2. HV relay assembly
  3. HV control ECU

WIRING DIAGRAM

See the wiring diagram of P0AA1-224. (Click here)

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes is required to discharge the high-voltage capacitor inside the w/ converter inverter assembly.

1.CHECK HARNESS AND CONNECTOR (HV CONTROL ECU - HV RELAY ASSEMBLY)

CAUTION:
Be sure to wear insulated gloves.



    A108053E01

  1. Turn the ignition switch off and remove the service plug grip. (Click here)

    NOTICE:
    Do not put the vehicle into the READY-on state with the service plug grip removed as this may cause a malfunction.

  1. Disconnect the H30 connector from the HV control ECU.

  1. Disconnect the S48 connector from the HV relay assembly.

  1. Measure the voltage according to the value(s) in the table below when the ignition switch is in the ON position.

    HINT:
    If the ignition switch is turned to the ON position with the service plug grip removed, the DTC (P0A0D-350) for the interlock switch system will be output.

    Standard Voltage :
    Tester Connection
    		Specified Condition
    CON2 (H30-2) - Body ground
    		Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    		Standard:
    CON2 (H30-2) - CON2 (S48-2)
    		Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    		Specified Condition
    CON2 (H30-2) or CON2 (S48-2) - Body ground
    		10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT HV RELAY ASSEMBLY (SMR2)

CAUTION:
Be sure to wear insulated gloves.



    A108055E07

  1. Turn the ignition switch off and remove the service plug grip. (Click here)

    NOTICE:
    Do not put the vehicle into the READY-on state with the service plug grip removed as this may cause a malfunction.

  1. Remove the HV relay assembly from the vehicle. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Specified Condition
    S47-1 - S44-1
    		Below 1 Ω
    (Apply auxiliary battery voltage between terminals (CON2 (S48-1) and GND (S48-4))

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Specified Condition
    CON2 (S48-1) - GND (S48-4)
    		20 to 60 Ω
    at -30 to 80 °C ( -22 to 176°F)



NG
REPLACE HV RELAY ASSEMBLY
OK

REPLACE HYBRID VEHICLE CONTROL ECU