ENGINE UNIT > DISASSEMBLY > Preparation
 | 09032-00100 | Oil Pan Seal Cutter |
 | 09201-01055 | Valve Guide Bushing Remover & Replacer 5.5 |
 | 09201-10000 | Valve Guide Bushing Remover & Replacer Set |
 | 09202-70020 | Valve Spring Compressor |
 | (09202-00010) | Attachment |
 | 09213-54015 | Crankshaft Pulley Holding Tool |
 | (91651-60855) | Bolt |
 | 09222-30010 | Connecting Rod Bushing Remover & Replacer |
 | 09228-07501 | Oil Filter Wrench |
 | 09330-00021 | Companion Flange Holding Tool |
 | 09950-50013 | Puller C Set |
 | (09951-05010) | Hanger 150 |
 | (09952-05010) | Slide Arm |
 | (09953-05020) | Center Bolt 150 |
 | (09954-05011) | Claw No.1 |
 | (09954-05031) | Claw No.3 |
 | 09950-70010 | Handle Set |
 | (09951-07100) | Handle 100 |
 | 09960-10010 | Variable Pin Wrench Set |
 | (09962-01000) | Variable Pin Wrench Arm Assy |
 | (09963-00500) | Pin 5 |
 | (09963-01000) | Pin 10 |
 | 09040-00010 | Hexagon Wrench Set . |
 | (09043-20080) | Socket Hexagon Wrench 8 |
 | (09043-20100) | Socket Hexagon Wrench 10 |
 | (09043-20120) | Socket Hexagon Wrench 12 |
 | (09043-30140) | Straight Hexagon Wrench 14 |
 | 09904-00010 | Expander Set |
 | (09904-00040) | No. 3 Claw |
| 99999-70008 | Cylinder gauge | |
| 99999-70009 | Dial indicator | |
| 99999-70012 | Feeler gauge | |
| 99999-70014 | Micrometer | |
| 99999-70023 | Straight edge | |
| 99999-70027 | Torque wrench | |
| 99999-70029 | Vernier calipers |
| 99999-60009 | V-block | |
| 99999-70034 | Plastigage | |
| 99999-90002 | Heater |
| CO/HC meter | |
| Feeler gauge | |
| Micrometer | |
| Tachometer | |
| Slide calipers | |
| Chain Block | |
| Universal engine lifter | |
| Deep Socket Wrench 24 mm | |
| Timing light | |
| Compression gauge | |
| Torx socket wrench (E6) | |
| 1.5 mm hexagon wrench | |
| 400-grit sandpaper | |
| Engine stand | |
| Insulated gloves | |
| Abrasive compound | Valve |
| Brush | Piston |
| Caliper gauge | |
| Carbide cutter (30°) | Valve seat |
| Carbide cutter (45°) | Valve seat |
| Carbide cutter (60°) | Valve seat |
| Connecting rod aligner | |
| Cylinder gauge | |
| Dial indicator | |
| Dye penetrant | |
| Groove cleaning tool | Piston ring groove |
| Heater | |
| Magnetic finger | |
| Micrometer | |
| Pin hole grinder | Connecting rod bush |
| Piston ring compressor | |
| Piston ring expander | |
| Plastigage | |
| Precision straight edge | |
| Press | |
| Razor brade | |
| Reamer (5.5 mm) | Valve guide bush |
| Ridge reamer | Cylinder |
| Soft brush | Cylinder head Cylinder block |
| Solvent | |
| Spring tester | Valve spring |
| Steel square | Valve spring |
| Thermometer | |
| Torque wrench | |
| Valve seat cutter | |
| Valve guide bushing brush | |
| V-block | |
| Vernier calipers | |
| Wire brush | Valve Cylinder head |
- HINT:
- Torx is a registered trademark of Textron Ine.
 | 09040-00011 | Hexagon Wrench Set | |
| (09043-20080) | Socket Hexagon Wrench 8 | |
| (09043-20100) | Socket Hexagon Wrench 10 | |
| (09043-20120) | Socket Hexagon Wrench 12 | |
| (09043-30140) | Straight Hexagon Wrench 14 | |
 | 09090-04020 | Engine Sling Device | |
 | 09200-00010 | Engine Adjust Kit | |
| 09904-00010 | Expander Set | |
| (09904-00040) | No. 3 Claw |
 | 08826-00080 | Seal Packing Black or equivalent (FIPG) | |
 | 08826-00100 | Seal Packing 1282B, THREE BOND 1282B or equivalent (FIPG) | |
 | 08833-00070 | Adhesive 1324, THREE BOND 1324 or equivalent |