DATA LIST / ACTIVE TEST
System information
| DATA LIST |
- HINT:
- With the intelligent tester connected to the DLC3 and the ignition switch ON, the ECB, ABS, and VSC data list can be displayed. Follow the prompts on the tester screen to access the DATA LIST.
| Item (Display) |
Measurement Item/ Range (Display) |
Normal Condition |
Diagnostic Note |
| ECB Motor Relay |
ECB motor relay / ON or OFF |
ON: Motor relay ON OFF: Motor relay OFF |
- |
| Main Idle SW |
Main idle switch / ON or OFF |
ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
| Stop Lamp SW |
Stop light switch / ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Parking Brake SW |
Parking brake switch / ON or OFF |
ON: Parking brake applied OFF: Parking brake released |
- |
| Shift Lever Position |
Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL |
- |
- |
| FR Wheel Speed |
Wheel speed sensor (FR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) |
Actual wheel speed |
Similar speed as indicated on speedometer |
| FL Wheel Speed |
Wheel speed sensor (FL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) |
Actual wheel speed |
Similar speed as indicated on speedometer |
| RR Wheel Speed |
Wheel speed sensor (RR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) |
Actual wheel speed |
Similar speed as indicated on speedometer |
| RL Wheel Speed |
Wheel speed sensor (RL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) |
Actual wheel speed |
Similar speed as indicated on speedometer |
| Deceleration Sensor |
Deceleration sensor 1 reading / min.: -18.52 m/s2, max.: -18.33 m/s2
|
Approximately m/s2 while stationary |
Reading changes when vehicle is bounced |
| Deceleration Sensor2 |
Deceleration sensor 2 reading / min.: -18.52 m/s2, max.: -18.33 m/s2
|
Approximately m/s2 while stationary |
Reading changes when vehicle is bounced |
| FR Speed Open |
FR speed sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| FL Speed Open |
FL speed sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| RR Speed Open |
RR speed sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| RL Speed Open |
RL speed sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| Yaw Rate Open |
Yaw rate sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| Deceleration Open |
Deceleration sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| Steering Open |
Steering angle sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| Master Cylinder Open |
Master cylinder pressure sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| ABS Warning Lamp |
ABS warning light / ON or OFF |
ON: Warning light ON OFF: Warning light OFF |
- |
| Brake Warning Lamp |
BRAKE warning light / ON or OFF |
ON: Warning light ON OFF: Warning light OFF |
- |
| Slip Indicator Lamp |
SLIP indicator light / ON or OFF |
ON: Indicator light ON OFF: Indicator light OFF |
- |
| Buzzer |
Skid control buzzer / ON or OFF |
ON: Buzzer ON OFF: Buzzer OFF |
- |
| VSC Warning Lamp |
VSC warning light / ON or OFF |
ON: Warning light ON OFF: Warning light OFF |
- |
| Vehicle Speed |
Maximum wheel speed sensor reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) |
Actual vehicle speed |
Speed indicated on speedometer |
| FR Wheel Acceleration |
FR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
|
Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- |
| FL Wheel Acceleration |
FL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
|
Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- |
| RR Wheel Acceleration |
RR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
|
Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- |
| RL Wheel Acceleration |
RL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
|
Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- |
| Zero Point of Decele |
Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
|
Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
- |
| Zero Point of Decele 2 |
Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
|
Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
- |
| Zero Point of Steering Angle |
Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg |
Min.: -3276.8 deg Max.: 3276.7 deg |
- |
| Lateral G |
Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2
|
Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
- |
| Forward and Rearward G |
Forward and rearward G / min.: -25.11 m/s2, max.: 24.91 m/s2
|
Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
- |
| Yaw Rate Value |
Yaw rate value / min.: -128 deg/s, max.: 127 deg/s |
Min.: -128 deg/s Max.: 127 deg/s |
- |
| Steering Angle Value |
Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg |
Min.: -3276.8 deg Max.: 3276.7 deg |
- |
| TRC(TRAC) Ctrl Status |
TRAC control status / ON or OFF |
ON: During the control |
- |
| TRC(TRAC) Brake Ctrl Status |
TRAC brake control status / ON or OFF |
ON: During the control |
- |
| FR Wheel VSC Ctrl Status |
FR wheel VSC control status / ON or OFF |
ON: During the control |
- |
| FL Wheel VSC Ctrl Status |
FL wheel VSC control status / ON or OFF |
ON: During the control |
- |
| RR Wheel VSC Ctrl Status |
RR wheel VSC control status / ON or OFF |
ON: During the control |
- |
| RL Wheel VSC Ctrl Status |
RL wheel VSC control status / ON or OFF |
ON: During the control |
- |
| Yaw Rate Sensor |
Yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s |
Min.: -128 deg/s Max.: 127 deg/s |
- |
| Yaw Rate Sensor 2 |
Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s |
Min.: -128 deg/s Max.: 127 deg/s |
- |
| Zero Point of Yaw Rate |
Memorized zero value / min.: -128 deg/s, max.: 127 deg/s |
Min.: -128 deg/s Max.: 127 deg/s |
- |
| Zero Point of Yaw Rate2 |
Memorized zero value / min.: -128 deg/s, max.: 127 deg/s |
Min.: -128 deg/s Max.: 127 deg/s |
- |
| Steering Angle Sensor |
Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg |
Left turn: Increase Right turn: Decrease |
- |
| Master Cylinder Sensor |
Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.3 to 0.9 V |
Reading increases when brake pedal is depressed |
| Master Cylinder Sensor2 |
Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.3 to 0.9 V |
Reading increases when brake pedal is depressed |
| FR Wheel ABS Ctrl Status |
FR wheel ABS control status / ON or OFF |
ON: During the control |
- |
| FL Wheel ABS Ctrl Status |
FL wheel ABS control status / ON or OFF |
ON: During the control |
- |
| RR Wheel ABS Ctrl Status |
RR wheel ABS control status / ON or OFF |
ON: During the control |
- |
| RL Wheel ABS Ctrl Status |
RL wheel ABS control status / ON or OFF |
ON: During the control |
- |
| BA Ctrl Status |
BA control status / ON or OFF |
ON: During the control |
- |
| PBA Ctrl Status |
PBA control status / ON or OFF |
ON: During the control |
- |
| Inspection Mode |
Inspection mode / OTHER or INSPECT |
- |
- |
| Number of IG ON(Inspection) |
Number of IG ON after entering the inspection mode / min.: 0, max.: 255 |
- |
- |
| Stroke Sensor |
Stroke sensor / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.7 to 1.3 V |
- |
| Stroke Sensor2 |
Stroke sensor 2 / min.: 0 V, max.: 5 V |
When brake pedal is released: 3.7 to 4.3 V |
- |
| Accumulator Sensor |
Accumulator pressure sensor / min.: 0 V, max.: 5 V |
Specified value: 3.2 to 4.0 V |
- |
| FR W/C Sensor |
FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.3 to 0.9 V |
- |
| FL W/C Sensor |
FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.3 to 0.9 V |
- |
| RR W/C Sensor |
RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.3 to 0.9 V |
- |
| RL W/C Sensor |
RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V |
When brake pedal is released: 0.3 to 0.9 V |
- |
| Reservoir Warning SW |
Brake fluid level warning switch / ON or OFF |
ON: Reservoir level normal OFF: Reservoir level low |
- |
| ECB Warning Lamp |
ECB warning light / ON or OFF |
ON: Warning light ON OFF: Warning light OFF |
- |
| FR Regenerative Request |
Front regenerative request torque / min.: 0 N*m, max.: 4,080 N*m |
- |
- |
| FR Regenerative Operation |
Front regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m |
- |
- |
| RR Regenerative Request |
Rear regenerative request torque / min.: 0 N*m, max.: 4,080 N*m |
- |
- |
| RR Regenerative Operation |
Rear regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m |
- |
- |
| Regenerative Cooperation |
Regenerative cooperation / ON or OFF |
ON: Operate |
- |
| OFF: Not operate |
- |
||
| ECB Motor Relay2 |
ECB motor relay 2 / ON or OFF |
ON: Motor relay ON OFF: Motor relay OFF |
- |
| ECB Main Relay |
ECB main relay / ON or OFF |
ON: Main relay ON OFF: Main relay OFF |
- |
| ECB Main Relay2 |
ECB main relay 2 / ON or OFF |
ON: Main relay ON OFF: Main relay OFF |
- |
| Voltage of M/C |
Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V |
- |
- |
| Voltage of M/C2 |
Voltage of master cylinder pressure sensor 2 / min.: -2.5 V, max.: 2.49 V |
- |
- |
| Voltage of Stroke Sensor |
Voltage of stroke sensor / min.: -2.5 V, max.: 2.49 V |
- |
- |
| Voltage of Stroke Sensor2 |
Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V |
- |
- |
| SLAFR Solenoid Current |
SLAFR solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLAFL Solenoid Current |
SLAFL solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLARR Solenoid Current |
SLARR solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLARL Solenoid Current |
SLARL solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLRFR Solenoid Current |
SLRFR solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLRFL Solenoid Current |
SLRFL solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLRRR Solenoid Current |
SLRRR solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| SLRRL Solenoid Current |
SLRRL solenoid current / min.: 0 A, max.: 3 A |
When brake pedal is released: 0 A |
- |
| Master Cylinder2 Open |
Master cylinder pressure sensor 2 open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| Stroke Open |
Stroke sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| FR Wheel Cylinder Open |
FR wheel cylinder pressure sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| FL Wheel Cylinder Open |
FL wheel cylinder pressure sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| RR Wheel Cylinder Open |
RR wheel cylinder pressure sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| RL Wheel Cylinder Open |
RL wheel cylinder pressure sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| Accumulator Open |
Accumulator pressure sensor open detection / ERROR or NORMAL |
ERROR: Momentary interruption NORMAL: Normal |
- |
| ECB Solenoid (SMC1) |
ECB solenoid (SMC1) / ON or OFF |
ON: Operate OFF: Not operate |
- |
| ECB Solenoid (SMC2) |
ECB solenoid (SMC2) / ON or OFF |
ON: Operate OFF: Not operate |
- |
| ECB Solenoid (SCSS) |
ECB solenoid (SCSS) / ON or OFF |
ON: Operate OFF: Not operate |
- |
| Number of DTC |
Number of DTC recorded / min.: 0, max.: 255 |
- |
- |
| ACTIVE TEST |
- HINT:
- Performing the Active Test using the intelligent tester allows the relay, actuator, etc. to operate without removing any parts. Performing the Active Test as the first step of troubleshooting is one of the methods to shorten labor time.
- It is possible to display the Data List during the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
According to the display on the tester, perform the Active Test.
- HINT:
- The ignition switch must be turned to the ON position to proceed to the Active Test using the intelligent tester.
ABS / VSC / TRAC: Item (Display)
Vehicle Condition / Test Details
Diagnostic Note
ABS Warning Lamp
Turns ABS warning light ON / OFF
Observe combination meter
VSC Warning Lamp
Turns VSC warning in multi information display ON / OFF
Observe combination meter
Brake Warning Lamp
Turns BRAKE warning light ON / OFF
Observe combination meter
Slip Indicator Lamp
Turns SLIP indicator light ON / OFF
Observe combination meter
ECB Warning Lamp
Turns brake control warning light ON / OFF
Observe combination meter
Buzzer
Turns skid control buzzer ON / OFF
Buzzer can be heard
Stop Lamp Relay
Turns stop light operation relay ON / OFF
Observe rear combination light (stop light) (Does not come on for 5 sec. or more)
ECB Main Relay
Turns ABS No.1 relay ON / OFF
Operating sound of relay (clicking sound) can be heard
ECB Main Relay2
Turns ABS No.2 relay ON / OFF
Operating sound of relay (clicking sound) can be heard
ECB Motor Relay
Turns ABS MTR1 motor relay ON / OFF
Operating sound of relay (clicking sound) can be heard
ECB Motor Relay2
Turns ABS MTR2 relay ON / OFF
Operating sound of relay (clicking sound) can be heard
ECB Solenoid (SMC1)
Turns ECB solenoid (SMC1) ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ECB Solenoid (SMC2)
Turns ECB solenoid (SMC2) ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ECB Solenoid (SCSS)
Turns ECB solenoid (SCSS) ON / OFF
Operating sound of solenoid (clicking sound) can be heard