RX400h · Service Manual RESTRAINTS

B0110/43

Diagnostic trouble codes

DESCRIPTION

The side squib RH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH (side squib RH).
The circuit instructs the SRS to deploy when deployment conditions are met.
DTC B0110/43 is recorded when a short circuit is detected in the side squib RH circuit.
DTC No.
 DTC Detecting Condition
 Trouble Area
B0110/43
  1. Short circuit between SFR+ wire harness and SFR- wire harness of side squib RH
  2. Side squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat side airbag assembly RH (Side squib RH)
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM

H001454E77

INSPECTION PROCEDURE


1. CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

  1. C110405E01
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat side airbag assembly RH.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire.

    CAUTION:
    Never connect a tester to the front seat side airbag assembly RH (Side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    Do not forcibly insert the SST into the terminals of the connector when connecting.
    Insert the SST straight into the terminals of the connector.

SST
09843-18060  

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0110/43 is not output.

    HINT:
    Codes other than DTC B0110/43 may be output at this time, but they are not related to this check.



 NG
Go to step 2
OK

REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY RH

2. CHECK CONNECTORS

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST (resistance 2.1 Ω) from the floor wire.

  1. Check that the floor wire connectors (on the front seat side airbag assembly RH side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



 NG
REPAIR OR REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)

  1. C110406E01
    Disconnect the connector from the center airbag sensor assembly.

  1. Release the activation prevention mechanism built into connector "B" (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    		 Condition
    		 Specified condition
    S9-1 (SFR+) -
    S9-2 (SFR-)
    		 Always
    		 1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C110407E01
    Connect the connectors to the front seat side airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0110/43 is not output.

    HINT:
    Codes other than code B0110/43 may be output at this time, but they are not related to this check.



 NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK


← B0108/52B0111/44 →