RX400h · Service Manual BODY

INSPECTION

Inspection


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (W/ MEMORY)

  1. B069418E04
    Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 1 (RMVR)
      Battery negative (-) → Terminal 10 (RM+R)
      		 Turns upward (A)
      Battery positive (+) → Terminal 10 (RM+R)
      Battery negative (-) → Terminal 1 (RMVR)
      		 Turns downward (B)
      Battery positive (+) → Terminal 9 (RMHR)
      Battery negative (-) → Terminal 10 (RM+R)
      		 Turns left (C)
      Battery positive (+) → Terminal 10 (RM+R)
      Battery negative (-) → Terminal 9 (RMHR)
      		 Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 4 (HTR+)
      Battery negative (-) → Terminal 12 (HTR-)
      		 Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		 Moves to retracted position and then stops
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 3 (MR)
      		 Moves to driving position and then stops

  1. B069691E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (EC+)
      Battery negative (-) → Terminal 15 (EC-)
      		 Mirror surface changes to dark


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (W/O MEMORY)

  1. B069699E01
    Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      		 Turns upward (A)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      		 Turns downward (B)
      Battery positive (+) → Terminal 4(MH)
      Battery negative (-) → Terminal 5 (M+)
      		 Turns left (C)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      		 Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 1 (HTR+)
      Battery negative (-) → Terminal 7 (HTR-)
      		 Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 10 (MR)
      		 Moves to retracted position and then stops
      Battery positive (+) → Terminal 10 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		 Moves to driving position and then stops

  1. B069719E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 2 (EC+)
      Battery negative (-) → Terminal 8 (EC-)
      		 Mirror surface changes to dark


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (W/ MEMORY)

  1. B069417E04
    Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 1 (LMVR)
      Battery negative (-) → Terminal 10 (LM+R)
      		 Turns upward (A)
      Battery positive (+) → Terminal 10 (LM+R)
      Battery negative (-) → Terminal 1 (LMVR)
      		 Turns downward (B)
      Battery positive (+) → Terminal 9 (LMHR)
      Battery negative (-) → Terminal 10 (LM+R)
      		 Turns left (C)
      Battery positive (+) → Terminal 10 (LM+R)
      Battery negative (-) → Terminal 9 (LMHR)
      		 Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 4 (HTR+)
      Battery negative (-) → Terminal 12 (HTR-)
      		 Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		 Moves to retracted position and then stops
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 3 (MR)
      		 Moves to driving position and then stops

  1. B069692E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (EC+)
      Battery negative (-) → Terminal 15 (EC-)
      		 Mirror surface changes to dark


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (W/O MEMORY)

  1. B069698E01
    Inspect outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      		 Turns upward (A)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      		 Turns downward (B)
      Battery positive (+) → Terminal 4 (MH)
      Battery negative (-) → Terminal 5 (M+)
      		 Turns left (C)
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      		 Turns right (D)

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 1 (HTR+)
      Battery negative (-) → Terminal 7 (HTR-)
      		 Mirror surface temperature becomes higher

  1. Inspect mirror retract operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 11 (MF)
      Battery negative (-) → Terminal 10 (MR)
      		 Moves to retracted position and then stops
      Battery positive (+) → Terminal 10 (MR)
      Battery negative (-) → Terminal 11 (MF)
      		 Moves to driving position and then stops

  1. B069718E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 4 (EC+)
      Battery negative (-) → Terminal 5 (EC-)
      		 Mirror surface changes to dark

← REMOVALINSTALLATION →