[ Model - ECLIPSE CROSS / Year - 2018 ]
DOOR LATCH ASSEMBLY INSPECTION
2018 / ECLIPSE CROSS / EC - Workshop Manual
42 -BODY > 42A-BODY > DOOR > ON-VEHICLE SERVICE > DOOR HANDLE AND LATCH INSPECTION
 
 
Check the door lock actuator operation in the following procedures:
1. Open a door that is supposed to be checked.
2. Remove a door trim assembly (Refer to GROUP 52A, Door Trim ).
3. Use a screwdriver or the like to slide the door latch claw from unlatch to full-latch position (Set the door latch from door-open to door-closed condition).
 
 
 
DOOR LOCK ACTUATOR <LH DRIVE VEHICLES>
 
 
ACTUATOR OPERATION CHECK <FRONT LH AND REAR LH>
Claw positionDoor inside handle lock knob positionBattery connectionDoor inside handle lock knob operation
Full-latchLock
  • Connect terminal 1 to negative battery terminal.
  • Connect terminal 2 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position.
Full-latchUnlock
  • Connect terminal 1 to positive battery terminal.
  • Connect terminal 2 to negative battery terminal.
Knob moves from "Unlock" to "Lock" position.
 
ACTUATOR OPERATION CHECK <FRONT RH AND REAR RH>
Claw positionDoor inside handle lock knob positionBattery connectionDoor inside handle lock knob operation
Full-latchLock
  • Connect terminal 4 to negative battery terminal.
  • Connect terminal 3 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position.
Full-latchUnlock
  • Connect terminal 4 to positive battery terminal.
  • Connect terminal 3 to negative battery terminal.
Knob moves from "Unlock" to "Lock" position.
 
ACTUATOR SWITCH CHECK <FRONT LH>
Claw positionDoor inside handle lock knob positionTester connectionSpecified condition
Full-latchLock6 - 8No continuity
Full-latchUnlock6 - 8Continuity exists (2 Ω or less)
 
ACTUATOR SWITCH CHECK <FRONT RH: VEHICLES WITH KOS>
Claw positionDoor inside handle lock knob positionTester connectionSpecified condition
Full-latchLock7 - 9No continuity
Full-latchUnlock7 - 9Continuity exists (2 Ω or less)
 
 
 
DOOR LOCK ACTUATOR <RH DRIVE VEHICLES WITHOUT DEAD LOCK SYSTEM)>
 
 
ACTUATOR OPERATION CHECK <FRONT RH AND REAR RH>
Claw positionDoor inside handle lock knob positionBattery connectionDoor inside handle lock knob operation
Full-latchLock
  • Connect terminal 4 to negative battery terminal.
  • Connect terminal 3 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position.
Full-latchUnlock
  • Connect terminal 4 to positive battery terminal.
  • Connect terminal 3 to negative battery terminal.
Knob moves from "Unlock" to "Lock" position.
 
ACTUATOR OPERATION CHECK <FRONT LH AND REAR LH>
Claw positionDoor inside handle lock knob positionBattery connectionDoor inside handle lock knob operation
Full-latchLock
  • Connect terminal 1 to negative battery terminal.
  • Connect terminal 2 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position.
Full-latchUnlock
  • Connect terminal 1 to positive battery terminal.
  • Connect terminal 2 to negative battery terminal.
Knob moves from "Unlock" to "Lock" position.
 
ACTUATOR SWITCH CHECK <FRONT RH>
Claw positionDoor inside handle lock knob positionTester connectionSpecified condition
Full-latchLock7 - 9No continuity
Full-latchUnlock7 - 9Continuity exists (2 Ω or less)
 
ACTUATOR SWITCH CHECK <FRONT LH: VEHICLES WITH KOS>
Claw positionDoor inside handle lock knob positionTester connectionSpecified condition
Full-latchLock6 - 8No continuity
Full-latchUnlock6 - 8Continuity exists (2 Ω or less)
 
 
 
DOOR LOCK ACTUATOR <RH DRIVE VEHICLES WITH DEAD LOCK SYSTEM>
After the inspection, check the dead lock system for correct operation in the following procedures:
1. Set the dead lock system on.
2. Unlock the door inside handle lock knob and check that the door latch claw does not unlatch by operating the door inside handle knob. When unlatching, replace the door latch assembly.
 
 
ACTUATOR OPERATION CHECK <FRONT RH AND REAR RH>
Claw positionDoor inside handle lock knob positionBattery connectionDoor inside handle lock knob operation
Full-latchLock
  • Connect terminal 4 to negative battery terminal.
  • Connect terminal 3 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position.
Full-latchUnlock
  • Connect terminal 4 to positive battery terminal.
  • Connect terminal 3 to negative battery terminal.
Knob moves from "Unlock" to "Lock" position.
Full-latchLock
  • Connect terminal 3 to negative battery terminal.
  • Connect terminal 10 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position but door latch claw does not unlatch with door inside handle knob operation (DEAD LOCK).
 
ACTUATOR OPERATION CHECK <FRONT LH AND REAR LH>
Claw positionDoor inside handle lock knob positionBattery connectionDoor inside handle lock knob operation
Full-latchLock
  • Connect terminal 1 to negative battery terminal.
  • Connect terminal 2 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position.
Full-latchUnlock
  • Connect terminal 1 to positive battery terminal.
  • Connect terminal 2 to negative battery terminal.
Knob moves from "Unlock" to "Lock" position.
Full-latchLock
  • Connect terminal 2 to negative battery terminal.
  • Connect terminal 5 to positive battery terminal.
Knob moves from "Lock" to "Unlock" position but door latch claw does not unlatch with door inside handle knob operation (DEAD LOCK).
 
ACTUATOR SWITCH CHECK <FRONT RH>
Claw positionDoor inside handle lock knob positionTester connectionSpecified condition
Full-latchLock7 - 9No continuity
Full-latchUnlock7 - 9Continuity exists (2 Ω or less)
 
ACTUATOR SWITCH CHECK <FRONT LH>
Claw positionDoor inside handle lock knob positionTester connectionSpecified condition
Full-latchLock6 - 8No continuity
Full-latchUnlock6 - 8Continuity exists (2 Ω or less)