[ Model - ECLIPSE CROSS / Year - 2018 ]
LEARNING PROCEDURES OF THE SUNROOF FULLY CLOSED POSITION
2018 / ECLIPSE CROSS / EC - Workshop Manual
42 -BODY > 42A-BODY > POWER PANORAMIC SUNROOF > ON-VEHICLE SERVICE > SUNROOF INITIALIZED ADJUSTMENT
 
 
SHIFTING CONDITIONS FOR THE FULLY CLOSED POSITION ADJUSTMENT MODE
 
 
<SLIDE GLASS PANEL AND ROLL SHADE (FRONT)>
  • When shifting to the forced fully closed position adjustment mode.
    How to shift to the forced fully closed position adjustment mode.
    1. Turn the ignition switch to the "ON" position.
    2. Move the slide glass panel and roll shade (front) to the position where it stops by closing operation, and then hold down the CLOSE switch for 10 seconds or more. Or, move the slide glass panel and roll shade (front) to the position where it stops by opening operation, and then hold down the OPEN switch for 10 seconds or more.
  • When the anti-trap function (safety mechanism) is activated consecutively five times
  • When the position information may be incorrect due to abnormal power supply during the slide glass panel and roll shade (front) operation
noteWhen installing the sunroof assembly, or installing/replacing the sunroof motor assembly or front shade motor assembly, operate the forced fully closed position adjustment mode to adjust the fully closed position.
 
 
<ROLL SHADE (REAR)>
  • When shifting to the forced fully closed position adjustment mode.
    How to shift to the forced fully closed position adjustment mode.
    1. Turn the ignition switch to the "ON" position.
    2. Move the roll shade (rear) to the position where it stops by closing operation, and then hold down the CLOSE switch for 10 seconds or more. Or, move the roll shade (rear) to the position where it stops by opening operation, and then hold down the OPEN switch for 10 seconds or more.
  • When the anti-trap function (safety mechanism) is activated consecutively five times
  • When the position information may be incorrect due to abnormal power supply during the roll shade (rear) operation
noteWhen installing the sunroof assembly, or installing/replacing the roll shade (rear) motor assembly, operate the forced fully closed position adjustment mode to adjust the fully closed position.
 
 
 
HOW TO ADJUST THE FULLY CLOSED POSITION
caution
  • Since the catch prevention function is invalid during initialisation operation, do not insert hands, arms, etc. in the operation area.
  • Do not perform learning when the battery deteriorates and the voltage is unstable. Perform learning with the engine started and the voltage stabilized.
  • Do not drive, or open or close the doors/gates/hood etc. during learning. If vibration occurs in the sunroof during learning, it may not be reversed at catching.
 
 
<SLIDE GLASS PANEL AND ROLL SHADE (FRONT)>
1. With the slide glass panel and roll shade (front) stopped, press and hold the CLOSE switch.
2. The sunroof lid glass repeats inching motion (moves approximately 30 mm and stops temporarily) in the CLOSE direction to the fully closed position, and then the front shade also moves to the fully closed position with inching motion.
noteIf you release your hand from the switch in the middle, you can resume the adjustment mode by holding down the switch again.
3. After both the slide glass panel and roll shade (front) have stopped at the fully closed position, release the switch that was being operated once and press it again within 6 seconds.
4. While holding down the switch, the front shade is opened ? the sunroof lid glass is opened ? the sunroof lid glass is closed ? the front shade is closed.
noteIf you release your hand from the switch in the middle, implement it again from the beginning.
5. After the operation stops, release the switch, and set the ignition switch to the "LOCK" (OFF) position.
 
 
<ROLL SHADE (REAR)>
1. With the roll shade (rear) stopped, press and hold the CLOSE switch.
2. The roll shade (rear) moves in the closing direction to the fully closed position repeating inching motion (moves approximately 30 mm and stops temporarily).
noteIf you release your hand from the switch in the middle, you can resume the adjustment mode by holding down the switch again.
3. After the roll shade (rear) has stopped at the fully closed position, release the switch that was being operated once and press it again within 6 seconds.
4. While holding down the switch, the roll shade (rear) is opened and closed.
noteIf you release your hand from the switch in the middle, implement it again from the beginning.
5. After the operation stops, release the switch, and set the ignition switch to the "LOCK" (OFF) position.