Mitsubishi Motors Service Manual

INSPECTION

2018 / ECLIPSE CROSS / EC - Workshop Manual

51 -EXTERIOR > OUTSIDE MIRROR > DOOR MIRROR > INSPECTION

REMOTE CONTROLLED DOOR MIRROR OPERATION CHECK

Remove the door trim, and then connect the battery to the door mirror assembly connector to check that the door mirror operates.

VEHICLE WITH CAMERA

Battery connection	Operation direction
Connect terminal No. 13 to the negative battery terminal. Connect terminal No. 4 to the positive battery terminal.	Up
Connect terminal No. 13 to the positive battery terminal. Connect terminal No. 4 to the negative battery terminal.	Down
Connect terminal No. 13 to the negative battery terminal. Connect terminal No. 12 to the positive battery terminal.	Right
Connect terminal No. 13 to the positive battery terminal. Connect terminal No. 12 to the negative battery terminal.	Left
Connect terminal No. 14 to the positive battery terminal. Connect terminal No. 5 to the negative battery terminal.	Retract
Connect terminal No. 14 to the negative battery terminal. Connect terminal No. 5 to the positive battery terminal.	Extend

VEHICLE WITHOUT CAMERA

Battery connection	Operation direction
Connect terminal No. 2 to the negative battery terminal. Connect terminal No. 1 to the positive battery terminal.	Up
Connect terminal No. 2 to the positive battery terminal. Connect terminal No. 1 to the negative battery terminal.	Down
Connect terminal No. 2 to the negative battery terminal. Connect terminal No. 3 to the positive battery terminal.	Right
Connect terminal No. 2 to the positive battery terminal. Connect terminal No. 3 to the negative battery terminal.	Left
Connect terminal No. 10 to the positive battery terminal. Connect terminal No. 9 to the negative battery terminal.	Retract
Connect terminal No. 10 to the negative battery terminal. Connect terminal No. 9 to the positive battery terminal.	Extend

REMOTE CONTROLLED MIRROR SWITCH CONTINUITY CHECK

Switch position		Tester connection	Specified condition
Left side	Up	1 - 4, 1 - 8, 2 - 10	Continuity exists(2 Ω or less)
	Down	1 - 2, 4 - 8, 4 - 10
	Right	1 - 2, 1 - 4, 8 - 10
	Left	1 - 8, 2 - 4, 2 - 10
Right side	Up	1 - 4, 1 - 7, 9 - 10
	Down	1 - 9, 4 - 7, 4 - 10
	Right	1 - 4, 1 - 9, 7 - 10
	Left	1 - 7, 4 - 9, 4 - 10
Retract and extend		1 - 3

HEATED DOOR MIRROR CHECK

caution

When relocating the car between locations with extremely different temperatures (warm and cold), leave the car in the location for a while to adapt to the temperature prior to checking it.

Check that the resistance value between the door mirror assembly connector terminal No. 1 and 9 <vehicles with camera>/No. 7 and 8 <vehicles without camera> is at the standard value.

Standard value: 7.2 ± 1.4 Ω at 25°C

BLIND SPOT WARNING LAMP CHECK

caution

Do not apply battery voltage to door mirror assembly connector No. 3 terminal as the blind spot warning lamp is broken.

Apply 5V to the door mirror assembly connector terminal No. 3 <vehicles with camera>/No. 4 <vehicles without camera>, earth the terminal No. 11 <vehicles with camera>/No. 5 <vehicles without camera>, and then check that the illumination lights up.

caution

Do not apply battery voltage to blind spot warning lamp connector No. 1 terminal as the blind spot warning lamp is broken.

Apply 5V to the blind spot warning lamp connector terminal No. 2, earth the terminal No. 1, and then check that the illumination lights up.

Checking the door mirror main wiring harness wires for continuity

Check the continuity between the door mirror assembly connector and the blind spot warning lamp connector.

Circuit	Tester connection	Specified condition
Power supply	Door mirror assembly connector terminal No. 3 - blind spot warning lamp connector terminal No. 2	Continuity exists(2 Ω or less)
Earth	Door mirror assembly connector terminal No. 11 - blind spot warning lamp connector terminal No. 1	Continuity exists(2 Ω or less)