[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
54 -CHASSIS ELECTRICAL > 54A-CHASSIS ELECTRICAL > SMARTPHONE LINK DISPLAY AUDIO > SYMPTOM PROCEDURES > NO SOUND.<Vehicles with audio amplifier><Vehicles with audio amplifier>
Inspection Procedure 2: No sound is heard. <Vehicles with audio amplifier>
 
 
cautionBefore replacing the multivision display, ensure that the power supply circuit, the earth circuit and the communication circuit are normal.
 
 
COMMENTS ON TROUBLE SYMPTOM
If the audio sound is not output, the multivision display may have a problem. In addition, if any of the speakers, tweeters or subwoofer is short-circuited, the protection circuit inside the multivision display disables all the speakers, tweeters or subwoofer to sound. Therefore, if all the speakers do not output sound, the speaker, tweeter or subwoofer circuit may be shorted or the speaker, tweeter, subwoofer or audio amplifier may be defective.
 
 
PROBABLE CAUSES
  • Malfunctions of multivision display
  • Malfunction of audio amplifier
  • Malfunctions of speaker, tweeter or subwoofer
  • Damaged harness wires and connectors
 
 
DIAGNOSIS PROCEDURE
STEP 1. Checking with audio speaker test.
Perform the audio speaker test, and check which speaker, tweeter or subwoofer does not output the sound.
Is the check result normal?
YES : The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
NO (No speakers, tweeters and subwoofer sound.) : Go to Step 2.
NO (No sound is heard from one of the speakers, tweeters or subwoofer.) : Go to Step 5.
 
STEP 2. Check the speaker, tweeter or subwoofer.
(1) Remove the speaker, tweeter or subwoofer.
 
(2) Check that the speaker, tweeter or subwoofer outputs the noise when the voltage of 5 V is applied to the speaker, tweeter or subwoofer connector terminal.
Is the check result normal?
Go to Step 3.
Replace the speaker, tweeter or subwoofer.
 
STEP 3. Check the wire harness between the speaker, tweeter or subwoofer connector terminal and the audio amplifier connector terminal.
Front door speaker (LH)
  • Check of short circuit in DFL+, DFL- line between front door speaker (LH) connector and audio amplifier connector.
Front door speaker (RH)
  • Check of short circuit in DFR+, DFR- line between front door speaker (RH) connector and audio amplifier connector.
Front tweeter (LH)
  • Check of short circuit in TFL+, TFL- line between front door speaker (LH) connector and audio amplifier connector.
Front tweeter (RH)
  • Check of short circuit in TFR+, TFR- line between front door speaker (RH) connector and audio amplifier connector.
Rear door speaker (LH)
  • Check of short circuit in RL+, RL- line between front door speaker (LH) connector and audio amplifier connector.
Rear door speaker (RH)
  • Check of short circuit in RR+, RR- line between front door speaker (RH) connector and audio amplifier connector.
Subwoofer
  • Check of short circuit in RW+, RW1+, RW-, RW1- line between subwoofer connector and audio amplifier connector.
Is the check result normal?
Go to Step 4.
Repair the connector(s) or wiring harness. (Replace the harness assembly because the aluminium harness cannot be repaired.)
 
STEP 4. Check of short to power supply, short to earth, and open circuit in FL+I, FL-I, FR+I, FR-I, RR+I and RR-I lines between audio amplifier connector and multivision display connector.
Is the check result normal?
Go to Step 8.
Repair the connector(s) or wiring harness.
 
STEP 5. Check the speaker, tweeter or subwoofer.
Follow the speaker test to check which speaker, tweeter or subwoofer does not sound.
(1) Remove the speaker, tweeter or subwoofer.
 
(2) Check that the speaker, tweeter or subwoofer outputs the noise when the voltage of 5 V is applied to the speaker, tweeter or subwoofer connector terminal.
Do the speaker output the noise?
Go to Step 6.
Replace the speaker, tweeter or subwoofer.
 
STEP 6. Check the wire harness between the speaker, tweeter or subwoofer connector terminal and audio amplifier connector terminal.
Follow the speaker test to check which speaker, tweeter or subwoofer circuit is defective.
Front door speaker (LH)
  • Check of short circuit in DFL+, DFL- line between front door speaker (LH) connector and audio amplifier connector.
Front door speaker (RH)
  • Check of short circuit in DFR+, DFR- line between front door speaker (RH) connector and audio amplifier connector.
Front tweeter (LH)
  • Check of short circuit in TFL+, TFL- line between front door speaker (LH) connector and audio amplifier connector.
Front tweeter (RH)
  • Check of short circuit in TFR+, TFR- line between front door speaker (RH) connector and audio amplifier connector.
Rear door speaker (LH)
  • Check of short circuit in RL+, RL- line between front door speaker (LH) connector and audio amplifier connector.
Rear door speaker (RH)
  • Check of short circuit in RR+, RR- line between front door speaker (RH) connector and audio amplifier connector.
Subwoofer
  • Check of short circuit in RW+, RW1+, RW-, RW1- line between subwoofer connector and audio amplifier connector.
Is the check result normal?
Go to Step 7.
Repair the connector(s) or wiring harness. (Replace the harness assembly because the aluminium harness cannot be repaired.)
 
STEP 7. Check of short to power supply, short to earth, and open circuit in FL+I, FL-I, FR+I, FR-I, RR+I and RR-I lines between audio amplifier connector and multivision display connector.
Is the check result normal?
Go to Step 8.
Repair the connector(s) or wiring harness.
 
STEP 8. Retest the system.
Replace the audio amplifier, then check that the audio sound is output.
Is the check result normal?
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).
Replace the multivision display (Refer to ).