P0732 SLEEVE A2 FUNCTION

NOTE：

• If DTC P0700 is detected, first diagnose the DTC P0700. Refer to DTC Logic (GT-R certified NISSAN dealer).
  
• If DTC P0715 is detected, first diagnose the DTC P0715. Refer to DTC Logic (GT-R certified NISSAN dealer).
  

• *1: A DTC is displayed when C or D in the DTC detection conditions is detected.
  
• *2: A DTC is displayed when F or G in the DTC detection conditions is detected.
  
• *3: A DTC is displayed when H, I, or J in the DTC detection conditions is detected.
  

DTC	Self-diagnosis name	DTC detection condition		Possible cause
P0732	2nd-4th position sensor voltage	A	A DTC is set if the 2nd-4th position sensor voltage value received by TCM is more than 4,700 mV. A DTC is set if the 2nd-4th position sensor voltage value received by TCM is less than 300 mV.	2nd-4th position sensor TCM Harness or connector (Open or short in the 2nd-4th position sensor circuit)
	Sleeve A2 function (long time release)	B	A DTC is set if the status of the sleeve A2 position of more than 1.3 mm (0.051 in) is detected for a certain period of time when the sleeve A2 position target is neutral. A DTC is set if the status of the sleeve A2 position of less than −1.3 mm (−0.051 in) is detected for a certain period of time when the sleeve A2 position target is neutral.	2nd-4th position sensor Shift solenoid valve 1 Shift solenoid valve 2 Sequence solenoid valve Harness or connector (Open or short in the 2nd-4th position sensor circuit) (Open or short in the shift solenoid valve 1 circuit) (Open or short in the shift solenoid valve 2 circuit) (Open or short in the sequence solenoid valve circuit)
	Sleeve A2 function (long time engagement)*1	C	A DTC is set if the status of the sleeve A2 position of less than 1.8 mm (0.071 in) is detected for a certain period of time when the sleeve A2 position target is on the 2nd gear side.
		D	A DTC is set if the status of the sleeve A2 position of more than −1.8 mm (−0.071 in) is detected for a certain period of time when the sleeve A2 position target is on the 4th gear side.
P0732	Sleeve A2 function (poor neutral hold)	E	A DTC is set if the status of the sleeve A2 position of more than 1.7 mm (0.067 in) or less than −1.7 mm (−0.067 in) is detected for a certain period of time when the sleeve A2 position target is neutral with the sleeve A1 engaged in the 6th gear.	2nd-4th position sensor Shift solenoid valve 1 Shift solenoid valve 2 Sequence solenoid valve Harness or connector (Open or short in the 2nd-4th position sensor circuit) (Open or short in the shift solenoid valve 1 circuit) (Open or short in the shift solenoid valve 2 circuit) (Open or short in the sequence solenoid valve circuit)
	Sleeve A2 function (poor gear engagement)*2	F	A DTC is set if the sleeve A2 position is 7.0 mm (0.276 in) or less and 1.7 mm (0.067 in) or more when the sleeve A2 position target is on the 2nd gear side.	Shift solenoid valve 1 Shift solenoid valve 2 Axis A feed pressure solenoid valve Sleeve A2 related part Harness or connector (Open or short in the shift solenoid valve 1 circuit) (Open or short in the shift solenoid valve 2 circuit) (Open or short in the axis A feed pressure solenoid valve circuit)
		G	A DTC is set if the sleeve A2 position is −1.7 mm (−0.067 in) or less and −7.1 mm (−0.28 in) or more when the sleeve A2 position target is on the 4th gear side.
	Sleeve A2 function (gear release)*3	H	A DTC is set if the following statuses 1 and 2 are detected. The difference between the clutch A speed calculated from the output shaft speed sensor value and clutch A speed sensor value is 1,000 rpm or more. The difference between the clutch A speed calculated from the vehicle speed signal (meter) (CAN signal) and clutch A speed sensor value is 1,000 rpm or more.	Clutch A speed sensor Sleeve A2 related part Harness or connector (Open or short in the clutch A speed sensor circuit)
		I	A DTC is set if the sleeve A1 and A2 positions are not in 2nd gear during driving in the 2nd gear.	Shift solenoid valve 1 Shift solenoid valve 2 Sleeve A2 related part Harness or connector (Open or short in the shift solenoid valve 1 circuit) (Open or short in the shift solenoid valve 2 circuit)
		J	A DTC is set if the sleeve A1 and A2 positions are not in 4th gear during driving in the 4th gear.

■ CAUTION ■

• If CONSULT-III is not available, “Diagnosis Procedure (GT-R certified NISSAN dealer)” must be performed before starting “DTC CONFIRMATION PROCEDURE”.
  
• If CONSULT-III is not available, never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
  
• Be careful of the driving speed.