Automatic transmission / transaxle
Preparation
PREPARATION ITEMS
AUTOMATIC TRANSMISSION / TRANSAXLE
SST
| Illustration |
Tool number |
Name |
Remarks |
|---|---|---|---|
 |
398527700 |
PULLER ASSY |
Used for removing extension housing rear oil seal. |
 |
09325-40010 |
TRANSMISSION OIL PLUG |
Used for installing extension housing rear oil seal. |
 |
498575400 |
PRESSURE GAUGE ADAPTER |
Used when measuring hydraulic pressure for line pressure. |
 |
18681AA040 |
OIL PRESSURE GAUGE ADAPTER |
Used when measuring hydraulic pressure for line pressure. |
 |
498897700 |
PRESSURE GAUGE ADAPTER SET |
Used when measuring hydraulic pressure for line pressure. |
 |
18750AA010 |
STOPPER |
·Used for removing automatic transmission ASSY from engine and installing it to engine. ·Used for preventing torque converter from falling. |
 |
18355AA000 |
PULLEY WRENCH |
Used for securing crank pulley. |
 |
18334AA000 |
PIN SET |
Used for securing crank pulley. |
 |
12281-38150 |
ENGINE HANGER |
Used for removing and installing automatic transmission ASSY. |
 |
90119-14120 |
BOLT |
Used for removing and installing automatic transmission ASSY. |
 |
99099AJ000 |
ENGINE HANGER |
Used for removing and installing automatic transmission ASSY. |
 |
18679AA020 |
ADJUSTER |
Used for removing and installing automatic transmission ASSY. |
 |
18632AA010 |
STAND ASSY |
Used for removing and installing automatic transmission ASSY. |
 |
498247001 |
MAGNET BASE |
Used for measuring runout, etc. |
 |
09351-32010 |
TOOL ONE-WAY CLUTCH TEST |
Used for unit inspection of torque converter. |
 |
09351-32020 |
STOPPER STATOR |
Used for unit inspection of torque converter. |
 |
09387-00110 |
CLUTCH COMPRESSION WRENCH |
Used for removing and installing NO. 1 clutch balancer. |
 |
09320-89010 |
COMPRESSOR TRANSFER CLUTCH SPR |
Used for removing and installing direct clutch piston SUB-ASSY. |
 |
09350-07050 |
COMPRESSOR PISTON SPR NO. 3 |
Used for removing and installing 1st & reverse brake return spring SUB-ASSY. |
 |
09350-07080 |
PULLER BRAKE REACTION SLEEVE |
Used for removing brake reaction sleeve. |
 |
09350-07090 |
BRAKE NO. 1 PISTON PULLER |
Used for removing NO. 4 brake piston. |
 |
09350-06120 |
MEASURE TERMINAL NO. 2 |
Used for measuring piston stroke of NO. 2 brake. |
 |
09350-07020 |
OIL PUMP PULLER |
Used for installing NO. 2 brake piston return spring SUB-ASSY. |
 |
09351-04020 |
SPRING COMPRESSOR NO. 1 |
Used for installing brake piston return spring SUB-ASSY. |
 |
09351-04010 |
PIPE |
Used for installing brake piston return spring SUB-ASSY. |
 |
09387-00070 |
WRENCH 1st & Rev BRAKE |
Used for installing No. 3 clutch balancer. |
 |
18762AA020 |
COMPRESSOR SPECIAL TOOL |
Used when assembling NO. 2 brake. |
 |
18762AA030 |
COMPRESSOR SPECIAL TOOL |
Used for disassembling NO. 3 brake cylinder ASSY. |
 |
1B023XG0 |
SUBARU SELECT MONITOR III KIT |
Used for diagnosing electrical system failure. |
GENERAL TOOL
| Tool name |
Remarks |
|---|---|
| Thickness gauge |
Used for adjusting select lever. |
| Socket hexagon |
Used for adjusting and replacing automatic transmission fluid. |
| Dial gauge |
Used for measuring runout, etc. |
| Roller probe |
Used for measuring runout, etc. |
| Caliper gauge |
Used for measuring clearance of each part, etc. |
| Screw shackle |
Automatic transmission ASSY |
| Circuit tester |
Used for measuring resistance and voltage. |
LUBRICANT, ETC.
| Name |
Part number |
Location of use |
|---|---|---|
| Auto fluid WS |
0888602305 (4 L) 0888602303 (20 L) |
·Automatic transmission ·O-ring ·Oil seal |
| Paint |
— |
Automatic transmission ASSY |
| THREE BOND 1281 or equivalent |
— |
Extension housing |
| THREE BOND 1344 or equivalent |
— |
·Fixing bolt for extension housing ·Fixing bolt for automatic transmission housing ·Fixing bolt for neutral start switch ASSY |
| NIGTIGHT LYW No.2 or equivalent |
— |
SHAFT |
| Multemp D or equivalent |
— |
Select lever |