MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Manual Transmission Assembly
1. Replace the differential side retainer oil seal with a new part.
NOTE:
Be sure to replace the differential side retainer oil seal after the removing the front drive shaft.
2. Install the rear cushion rubber to the transmission assembly.
Tightening torque:
35 N·m (3.6 kgf-m, 26 ft-lb)
4. Install the transmission onto the engine.
(1) Gradually raise the transmission with the transmission jack.
(2) Engage at the spline section.
NOTE:
Be careful not to hit the main shaft against the clutch cover.
5. Install the transmission rear crossmember.
Tightening torque:
T1: 70 N·m (7.1 kgf-m, 52 ft-lb)
T2: 140 N·m (14.3 kgf-m, 103 ft-lb)
6. Take out the transmission jack.
7. Tighten the nuts which hold lower side of transmission to the engine.
Tightening torque:
50 N·m (5.1 kgf-m, 37 ft-lb)
8. Connect the engine and transmission.
(2) Tighten the bolt which holds the right upper side of transmission to the engine.
Tightening torque:
50 N·m (5.1 kgf-m, 37 ft-lb)
9. Remove the ST.
10. Install the pitching stopper.
Tightening torque:
T1: 50 N·m (5.1 kgf-m, 37 ft-lb)
T2: 58 N·m (5.9 kgf-m, 43 ft-lb)
11. Lift up the vehicle.
12. Install the front drive shaft into the transmission.
ST 28399SA010 | FRONT DRIVE SHAFT OIL SEAL PROTECTOR |
13. Insert the ball joints of the lower arm into the housing, then tighten the installing bolts.
Tightening torque:
49 N·m (5.0 kgf-m, 36 ft-lb)
(A) |
Transverse link |
(B) |
Ball joint |
14. Attach the stabilizer link to the transverse link.
Tightening torque:
45 N·m (4.6 kgf-m, 33 ft-lb)
15. Attach the gear shift rod and stay.
(1) Attach the gear shift rod to the transmission.
Tightening torque:
18 N·m (1.8 kgf-m, 13.0 ft-lb)
(A) |
Stay |
(B) |
Gear shift rod |
(2) Attach the stay to the transmission.
Tightening torque:
18 N·m (1.8 kgf-m, 13.0 ft-lb)
17. Connect cooler hose to the oil pipe. (Models with oil pump)
18. Install the heat shield cover. (If equipped)
19. Install the hanger bracket on the right side of the transmission.
20. Install the rear exhaust pipe and muffler.
23. Install the under cover.
24. Install the operating cylinder.
Tightening torque:
37 N·m (3.8 kgf-m, 27.5 ft-lb)
25. Install the transmission drive select cable. (Dual range model)
(A) |
Snap pin |
(B) |
Clevis pin |
(C) |
Drive select cable |
26. Connect the following connectors.
(1) Transmission ground cable
Tightening torque:
13 N·m (1.3 kgf-m, 9.4 ft-lb)
(2) Vehicle speed sensor connector
(3) Neutral position switch connector
(4) Back-up light switch connector
(5) High-low switch connector (Dual range model)
27. Install the air cleaner case stay.
31. Connect the ground cable to battery.
32. Lower the vehicle from the lift arms.