Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Read the DATA LIST according to the display on the tester.

    ECM (Cruise control): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    VEHICLE SPD
    Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    MEMORY SPD
    Cruise control memorized speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual stored vehicle speed
    -
    THROTTLE
    Required throttle opening angle / min. : 0°, max. : 125°
    Actual required throttle opening
    -
    CRUISE CONTROL
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    MAIN SW (MAIN)
    Main switch signal (Main CPU) / ON or OFF
    ON: Main switch on (Pushed on)
    OFF: Main switch off (Pushed off)
    "3"
    MAIN SW (SUB)
    Main SW signal (Sub CPU) / ON or OFF
    ON: Main SW ON (Pressed in)
    OFF: Main SW OFF (Pressed out)
    "3"
    CCS READY M
    Cruise control system standby condition (Main CPU) / ON or OFF
    ON / OFF: Change ON/OFF each time Main SW is pushed in.
    "1"
    CCS READY S
    Cruise control system standby condition (Sub CPU) / ON or OFF
    ON / OFF: Change ON/OFF each time Main SW is pushed in.
    "1"
    CCS INDICATOR M
    Cruise indicator signal (Main CPU) / ON or OFF
    ON: "CCS READY" ON
    OFF: "CCS READY" OFF
    "2"
    CCS INDICATOR S
    Cruise indicator signal (Sub CPU) / ON or OFF
    ON: "CCS READY" ON
    OFF: "CCS READY" OFF
    "2"
    CANCEL SW
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST SW
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    RES/ACC SW
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -
    STP LIGHT SW2 M
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    STP LIGHT SW2 S
    Stop light switch signal (Sub CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    STP LIGHT SW1 S
    Stop light switch signal (Sub CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    SHIFT D POS
    PNP switch signal (D position) / ON or OFF
    ON: Shift lever in D
    OFF: Shift lever not in D
    -

    HINT:
    1. "3" is OK but "1" is NG → ECM failure
    2. "1" is OK but "2" is NG → DTC output or ECM failure
    3. "3" is OK but CRUISE main indicator light does not illuminate → CRUISE main indicator light, wire harness, or ECM failure