Home › ENGINE ยท 1GR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR


A075654E06
  1. Install a new insulator onto each fuel injector.

  1. Apply a light coat of spindle oil or gasoline to a new O-ring and install it onto each fuel injector.



    A075655E04
  1. While turning the fuel injector left and right, install it onto the fuel delivery pipe.

  1. Position the fuel injector connector facing outward.



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


A075656E03
  1. Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.

  1. Provisionally install the 6 bolts, which are used to hold the fuel delivery pipe, onto the intake manifold.

  1. Check that the fuel injectors rotate smoothly.

    HINT:
    If the fuel injectors do not rotate smoothly, replace the O-ring.

  1. Position the fuel injector connector facing outward.

  1. Tighten the 6 bolts, which are used to hold the fuel delivery pipe, to the intake manifold.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Connect the 6 fuel injector connectors.



3. CONNECT FUEL PIPE SUB-ASSEMBLY
  1. Push the tube connector into the pipe until the tube connector makes a "click" sound.

    NOTICE:
    1. Check if there is any damage or foreign objects on the connected part of the fuel pipe.
    2. After connecting, check that the pipe and connector are securely connected by pulling them.

  1. Install the fuel pipe clamp.



4. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
  1. Push the tube connector into the pipe until the tube connector makes a "click" sound.

    NOTICE:
    1. Check if there is any damage or foreign objects on the connected part of the fuel pipe.
    2. After connecting, check that the pipe and connector are securely connected by pulling them.

  1. Install the fuel pipe clamp.



5. INSTALL INTAKE AIR SURGE TANK


    A075648E02
  1. Install a new gasket and the intake air surge tank with the 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Using an 8 mm socket hexagon wrench, install the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    A075647E01
  1. Install the 3 upper bolts which are used to secure the 2 surge tank stays and throttle body bracket.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



    A075646E01
  1. Install the 3 wire harness clamps and hose clamp.

  1. Connect the throttle motor connector.

  1. Connect the 2 VSV connectors.



    A075645E01
  1. Connect the ventilation hose.



    A075644E01
  1. Connect the fuel vapor feed hose.



    A075598E01
  1. Connect the No. 4 water by-pass hose.



    A075597E01
  1. Connect the No. 5 water by-pass hose.



6. INSTALL AIR CLEANER ASSEMBLY


    A075596E01
  1. Install the air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamps.



    A075595E01
  1. Install the 2 wire harness clamps.

  1. Connect the mass air flow meter connector.

  1. Connect the vacuum hose.



    A075594E01
  1. Connect the ventilation hose No. 2.



7. CONNECT NO. 2 VENTILATION HOSE


    A075594E01
  1. Connect the No. 2 ventilation hose.



8. INSTALL V-BANK COVER


    A075593E01
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



9. CONNECT BATTERY NEGATIVE TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



10. ADD ENGINE COOLANT
  1. Slowly fill the system with engine coolant.

    Capacity:
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Install the radiator cap securely.

  1. Bleed the cooling system.

    1. Open the heater water valve while warming up the engine.

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Add coolant into the reservoir until the coolant level is FULL.



11. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



12. CHECK FOR FUEL LEAKAGE