DTC P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) |
DTC P0332 Knock Sensor 2 Circuit Low Input (Bank 2) |
DTC P0333 Knock Sensor 2 Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0327 P0332 | Output voltage of knock sensor 1 or 2 is less than 0.5 V (1 trip detection logic) |
|
| P0328 P0333 | Output voltage of knock sensor 1 or 2 is more than 4.5 V (1 trip detection logic) |
|

| Item | Content |
| Terminals | KNK1 - EKNK or KNK2 -EKN2 |
| Equipment Settings | 0.01 to 10 V/DIV. 0.01 to 10 msec./DIV. |
| Conditions | Keep engine speed at 4,000 rpm with warm engine |
| Related DTCs | P0327: Knock sensor (Bank 1) open/short (Low voltage) P0328: Knock sensor (Bank 1) open/short (High voltage) P0332: Knock sensor (Bank 2) open/short (Low voltage) P0333: Knock sensor (Bank 2) open/short (High voltage) |
| Required Sensors/Components (Main) | Knock sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, Camshaft position sensor, Engine coolant temperature sensor, Mass air flow meter |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 10.5 V or more |
| Time after engine start | 5 seconds or more |
| Ignition switch | ON |
| Starter | OFF |
| Knock sensor voltage | Less than 0.5 V |
| Knock sensor voltage | More than 4.5 V |

| 1.READ OUTPUT DTC (CHECK KNOCK SENSOR CIRCUIT) |
![]() |
Disconnect the EB1 connector.
Using lead wires, connect the EB1 connectors as follows.
| Male Connector - Female Connector |
| Terminal 6 - Terminal 2 |
| Terminal 2 - Terminal 6 |
| Terminal 7 - Terminal 8 |
| Terminal 8 - Terminal 7 |
Warm up the engine.
Race the engine at 3,000 rpm for 10 seconds or more.
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II/ DTC INFO / CURRENT CODES.
Read DTCs.
| Display | Proceed to |
| DTCs same as when vehicle brought in P0327, P0328 → P0327, P0328 or P0332, P0333 → P0332, P0333 | A |
| DTCs different from when vehicle brought in P0327, P0328 → P0332, P0333 or P0332, P0333 → P0327, P0328 | B |
Reconnect the EB1 connector.
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM) |
![]() |
Disconnect the EB1 connector.
Disconnect the E5 ECM connector.
Check the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| EB1 female connector 6 - KNK1 (E5-29) | Below 1 Ω |
| EB1 female connector 7 - EKNK (E5-28) | Below 1 Ω |
| EB1 female connector 2 - KNK2 (E5-21) | Below 1 Ω |
| EB1 female connector 8 - EKN2 (E5-20) | Below 1 Ω |
| Tester Connection | Specified Condition |
| EB1 female connector 6 or KNK1 (E5-29) - Body ground | 10 kΩ or higher |
| EB1 female connector 7 or EKNK (E5-28) - Body ground | 10 kΩ or higher |
| EB1 female connector 2 or KNK2 (E5-21) - Body ground | 10 kΩ or higher |
| EB1 female connector 8 or EKN2 (E5-20) - Body ground | 10 kΩ or higher |
Reconnect the EB1 connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM |
![]() |
Disconnect the E5 ECM connector.
Turn the ignition switch to ON.
Measure the voltage between the specified ECM terminals.
| Tester Connection | Specified Condition |
| KNK1 (E5-29) - EKNK (E5-28) | 4.5 to 5.5 V |
| KNK2 (E5-21) - EKN2 (E5-20) | 4.5 to 5.5 V |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.CHECK FOR INTERMITTENT PROBLEMS |
| NEXT | ||
| ||
| 5.INSPECT KNOCK SENSOR |
![]() |
Disconnect the EB1 connector.
Measure the resistance of the EB1 male connector.
| Tester Connection | Specified Condition |
| EB4 male connector 3 - 4 | 120 to 280 kΩ |
| EB4 male connector 7 - 8 |
Reconnect the EB1 connector.
|
| ||||
| NG | |
| 6.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR) |
Check harness and connector between EB1 connector and the knock sensors.
|
| ||||
| OK | ||
| ||