Home › ENGINE ยท 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



ECM
*: Shielded

A121603E05

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltage column. The illustration above can be used as a reference to identify the ECM terminal locations.


Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
STD Voltage
BATT (E8-3) - E1 (E6-1)
L - W-B
Battery (for measuring the battery voltage and for the ECM memory)
Always
9 to 14 V
+BM (E8-7) - E1 (E6-1)
GR - W-B
Power source of throttle motor
Always
9 to 14 V
IGSW (E8-9) - E1 (E6-1)
B-O - W-B
Ignition switch
Ignition switch ON
9 to 14 V
+B (E8-1) - E1 (E6-1)
B - W-B
Power source of ECM
Ignition switch ON
9 to 14 V
+B2 (E8-2) - E1 (E6-1)
B - W-B
Power source of ECM
Ignition switch ON
9 to 14 V
MREL (E8-8) - E1 (E6-1)
W-G - W-B
EFI relay
Ignition switch ON
9 to 14 V
VC (E4-23) - E2 (E4-28)
L-R - BR
Power source for sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
VG (E4-30) - E2G (E4-29)
W-R - B-W
Mass air flow meter
Idling, shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
THA (E4-22) - E2 (E4-28)
Y-B - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
THW (E4-21) - E2 (E4-28)
R-L - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
VTA1 (E4-20) - E2 (E4-28)
Y - BR
Throttle position sensor (for engine control)
Ignition switch ON, throttle valve fully closed
0.5 to 1.2 V
VTA1 (E4-20) - E2 (E4-28)
Y - BR
Throttle position sensor (for engine control)
Ignition switch ON, throttle valve fully open
3.2 to 4.8 V
VTA2 (E4-19) - E2 (E4-28)
R-B - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, throttle valve fully open
2.1 to 3.1 V
VTA2 (E4-19) - E2 (E4-28)
R-B - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, throttle valve fully open
4.5 to 5.5 V
VPA (E8-18) - EPA (E8-20)
W-R - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, throttle valve fully closed
0.5 to 1.1 V
VPA (E8-18) - EPA (E8-20)
W-R - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, throttle valve fully open
2.6 to 4.5 V
VPA2 (E8-19) - EPA2 (E8-21)
R-B - V-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, throttle valve fully closed
1.2 to 2.0 V
OC1+ (E6-17) - OC1- (E6-16)
P - LG
Camshaft timing oil control valve (OCV)
Idling
Pulse generation
(See waveform 3)
OC2+ (E6-15) - OC2- (E6-14)
R-W - Y-R
Camshaft timing oil control valve (OCV)
Idling
Pulse generation
(See waveform 3)
VV1+ (E6-25) - VV1- (E6-24)
Y* - L*
Variable valve timing (VVT) sensor (Bank 1)
Idling
Pulse generation
(See waveform 4)
VV2+ (E6-18) - VV2- (E6-28)
R* - G*
Variable valve timing (VVT) sensor (Bank 2)
Idling
Pulse generation
(See waveform 4)
M+ (E4-5) - E1 (E6-1)
R* - W-B
Throttle motor
Idling
Pulse generation
(See waveform 7)
M- (E4-4) - E1 (E6-1)
G* - W-B
Throttle motor
Idling
Pulse generation
(See waveform 8)
A1A+ (E5-22) - E1 (E6-1)
Y* - W-B
A/F sensor
Ignition switch ON

A1A- (E5-30) - E1 (E6-1)
BR* - W-B
A/F sensor
Ignition switch ON

A2A+ (E5-23) - E1 (E6-1)
P* - W-B
A/F sensor
Ignition switch ON

A2A- (E5-31) - E1 (E6-1)
L* - W-B
A/F sensor
Ignition switch ON

HA1A (E5-2) - E1 (E6-1)
R-L - W-B
A/F sensor heater
Idling

HA2A (E5-1) - E1 (E6-1)
B-W - W-B
A/F sensor heater
Ignition switch ON

VPA2 (E8-19) - EPA2 (E8-21)
R-B - V-W
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, throttle valve fully open
3.4 to 5.3 V
VCPA (E8-26) - EPA (E8-20)
B-Y - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
VCP2 (E8-27) - EPA2 (E8-21)
W-L - V-W
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
OX1B (E4-18) - E1 (E6-1)
B* - W-B
Heated oxygen sensor
Maintain engine speed at 2,500 rpm for 2 minutes after warming up
Pulse generation
(See waveform 10)
OX2B (E5-33) - E1 (E6-1)
W* - W-B
HT1B (E4-1) - E1 (E6-1)
G-Y - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
HT2B (E5-5) - E1 (E6-1)
P - W-B
HT1B (E4-1) - E1 (E6-1)
G-Y - W-B
Heated oxygen sensor heater
Ignition switch ON
9 to 14 V
HT2B (E5-5) - E1 (E6-1)
P - W-B
#10 (E6-2) - E01 (E4-7)
R-L - W-B
Injector
Ignition switch ON
9 to 14 V
#20 (E6-3) - E01 (E4-7)
L - W-B
#30 (E6-4) - E01 (E4-7)
W - W-B
#40 (E6-5) - E01 (E4-7)
Y - W-B
#50 (E6-6) - E01 (E4-7)
G - W-B
#60 (E6-7) - E01 (E4-7)
R - W-B
#70 (E4-3) - E01 (E4-7)
W - W-B
#80 (E4-2) - E01 (E4-7)
BR - W-B
#10 (E6-2) - E01 (E4-7)
R-L - W-B
Injector
Idling
Pulse generation
(See waveform 1)
#20 (E6-3) - E01 (E4-7)
L - W-B
#30 (E6-4) - E01 (E4-7)
W - W-B
#40 (E6-5) - E01 (E4-7)
Y - W-B
#50 (E6-6) - E01 (E4-7)
G - W-B
#60 (E6-7) - E01 (E4-7)
R - W-B
#70 (E4-3) - E01 (E4-7)
W - W-B
#80 (E4-2) - E01 (E4-7)
BR - W-B
KNK1 (E5-29) - EKNK (E5-28)
G* - R*
Knock sensor
Maintain engine speed at 4,000 rpm after warming up
Pulse generation
(See waveform 2)
KNK2 (E5-21) - EKN2 (E5-20)
W* - B*
Knock sensor
Maintain engine speed at 4,000 rpm after warming up
Pulse generation
(See waveform 2)
G2+ (E6-19) - G2- (E6-29)
B - W
Camshaft position sensor
Idling
Pulse generation
(See waveform 5)
NE+ (E6-21) - NE- (E6-20)
L* - Y*
Crankshaft position sensor
Idling
Pulse generation
(See waveform 5)
PRG (E4-34) - E1 (E6-1)
Y-R - W-B
VSV for EVAP
Ignition switch ON
9 to 14 V
SPD (E7-8) - E1 (E6-1)
V-R - W-B
Speed signal from combination meter
Ignition switch ON, Rotate driving wheel slowly
Pulse generation
(See waveform 6)
FPR (E6-30) - E1 (E6-1)
G-R - W-B
Fuel pump relay
Ignition switch ON
0 to 3.0 V
FC (E8-10) - E1 (E6-1)
GR-B - W-B
Fuel pump control
Ignition switch ON
9 to 14 V
IGT1 (E4-8) - E1 (E6-1)
LG - W-B
Ignition coil with igniter (ignition signal)
Idling
Pulse generation
(See waveform 9)
IGT2 (E4-15) - E1 (E6-1)
LG-B - W-B
IGT3 (E4-11) - E1 (E6-1)
L-W - W-B
IGT4 (E4-10) - E1 (E6-1)
L-Y - W-B
IGT5 (E4-13) - E1 (E6-1)
B-L - W-B
IGT6 (E4-12) - E1 (E6-1)
G - W-B
IGT7 (E4-14) - E1 (E6-1)
G-W - W-B
IGT8 (E4-9) - E1 (E6-1)
G-B - W-B
IGF1 (E4-24) - E1 (E6-1)
R-Y - W-B
Ignition coil with igniter (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
IGF2 (E4-25) - E1 (E6-1)
R-W - W-B
IGF1 (E4-24) - E1 (E6-1)
R-Y - W-B
Ignition coil with igniter (ignition confirmation signal)
Idling
Pulse generation
(See waveform 9)
IGF2 (E4-25) - E1 (E6-1)
R-W - W-B
STP (E8-15) - E1 (E6-1)
G-Y - W-B
Stop light switch
Brake pedal depressed
7.5 to 14 V
STP (E8-15) - E1 (E6-1)
G-Y - W-B
Stop light switch
Brake pedal released
Below 1.5 V
ST1- (E8-16) - E1 (E6-1)
R-L - W-B
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
ST1- (E8-16) - E1 (E6-1)
R-L - W-B
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal released
7.5 to 14 V
STAR/NSW (E5-8) - E1 (E6-1)
P - W-B
Park/Neutral position switch
Ignition switch ON, Shift lever position other than P and N
9 to 14 V
STAR/NSW (E5-8) - E1 (E6-1)
P - W-B
Park/Neutral position switch
Ignition switch ON, Shift lever position in P, N
Below 3.0 V
W (E7-30) - E1 (E6-1)
R-B - W-B
MIL
Idling
9 to 14 V
W (E7-30) - E1 (E6-1)
R-B - W-B
MIL
Ignition switch ON
Below 3.0 V
ELS1 (E7-13) - E1 (E6-1)
G - W-B
Electric load
Taillight switch ON, Defogger switch ON
7.5 to 14 V
ELS2 (E7-12) - E1 (E6-1)
Y-G - W-B
Electric load
Taillight switch OFF, Defogger switch OFF
0 to 1.5 V
TACH (E7-1) - E1 (E6-1)
B-W - W-B
Engine speed
Idling
Pulse generation
(See waveform 11)
TC (E8-23) - E1 (E6-1)
P-L - W-B
Terminal TC of DLC3
Ignition switch ON
9 to 14 V
STA (E6-11) - E1 (E6-1)
B-Y - W-B
Starter signal
Cranking
6 V or higher
STA (E6-11) - E1 (E6-1)
B-Y - W-B
Park/neutral position switch
Shift lever position P or N, Ignition switch START
9 to 14 V
STSW (E6-12) - E1 (E6-1)
L-Y - W-B
STA No. 2 fuse
Shift lever position P or N, Ignition switch START
9 to 14 V
VPMP (E8-5) - E1 (E6-1)
R-G - W-B
Canister closed valve
Ignition switch ON
9 V to 14 V
MPMP (E8-6) - E1 (E6-1)
O - W-B
Leak detection pump
Vacuum pump OFF
0 V to 3 V
MPMP (E8-6) - E1 (E6-1)
O - W-B
Leak detection pump
Vacuum pump ON
9 V to 14 V
PPMP (E8-22) - E1 (E6-1)
R - W-B
Vapor pressure sensor
Ignition switch ON
3 V to 3.6 V
AIV1 (E4-27) - E1 (E6-1)
P - W-B
VSV for air injection control (Bank 1)
Ignition switch ON
9 to 14 V
AIV2 (E4-26) - E1 (E6-1)
L - W-B
VSV for air injection control (Bank 2)
Ignition switch ON
9 to 14 V
AIRV (E8-4) - E1 (E6-1)
Y - W-B
AI driver (ASV control signal)
Ignition switch ON
9 to 14 V
AIRP (E8-25) - E1 (E6-1)
G - W-B
AI driver (Air pump control signal)
Ignition switch ON
9 to 14 V
AIP (E4-32) - E1 (E6-1)
W-L - W-B
Air pressure sensor
Ignition switch ON
3 V to 3.6 V


    A093279E06
  1. WAVEFORM 1
    Fuel injector 
    ECM Terminal Names
    Between #10 (to #40) and E01
    Tester Range
    20 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as engine rpm increases.



  2. A085286E15
  3. WAVEFORM 2
    Knock sensor 
    ECM Terminal Name
    Between KNK1 and EKNK
    Between KNK2 and EKN2
    Tester Range
    1 V/DIV., 1 msec./DIV.
    Condition
    Maintain engine RPM at 2,000 rpm after engine warmed-up

    HINT:
    1. The wavelength becomes shorter as engine rpm increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.



  4. A093281E07
  5. WAVEFORM 3
    Camshaft timing oil control valve (OCV) 
    ECM Terminal Name
    Between OC1+ and OC1-
    Between OC2+ and OC2-
    Tester Range
    0.2 V/DIV., 200 msec./DIV.
    Condition
    Accelerate slowly after engine warmed-up

    HINT:
    In the DATA LIST, the items VVT OCV DUTY B1 and B2 show the duty ratio of voltage flowing to the OCV (see illustration).
    VVT OCV DUTY B1, B2 = A/B x 100 (%)



  6. A085260E11
  7. WAVEFORM 4
    Variable Valve Timing (VVT) sensor (bank 1, 2) and Crankshaft position sensor 
    ECM Terminal Name
    CH1: Between VV1+ and VV1-
    CH2: Between VV2+ and VV2-
    CH3: Between NE+ and NE-
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idle after engine warmed-up

    HINT:
    The wavelength becomes shorter as engine rpm increases.



  8. A138873E01
  9. WAVEFORM 5
    Camshaft position sensor and Crankshaft position sensor 
    ECM Terminal Name
    Between G2+ and G2-
    Tester Range
    2 V/DIV, 200 msec./DIV
    Condition
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as the engine rpm increases.



  10. A093224E18
  11. WAVEFORM 6
    Vehicle speed signal 
    ECM Terminal Name
    Between SPD2+ and SPD2-
    Tester Range
    5 V/DIV., 10 msec./DIV.
    Condition
    Driving by 40 km/h (25 mph)

    HINT:
    The wavelength becomes shorter as engine rpm increases.



  12. A093274E10
  13. WAVEFORM 7
    Throttle actuator positive terminal 
    ECM Terminal Name
    Between M+ and ME01
    Tester Range
    5 V/DIV., 1 msec./DIV.
    Condition
    Idle after engine warmed-up

    HINT:
    The duty ratio varies depending on the throttle opening operation.



  14. A093275E09
  15. WAVEFORM 8
    Throttle actuator negative terminal 
    ECM Terminal Name
    Between M- and ME01
    Tester Range
    5 V/DIV., 1 msec./DIV.
    Condition
    Idle after engine warmed-up

    HINT:
    The duty ratio varies depending on the throttle opening operation.



  16. A093278E14
  17. WAVEFORM 9
    Igniter IGT signal (from ECM to igniter) and Igniter IGF signal (from igniter to ECM) 
    ECM Terminal Name
    (a) Between IGT1 (to IGT8) and E1
    (b) Between IGF1 (IGF2) and E1
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as engine rpm increases.



  18. A088863E13
  19. WAVEFORM 10
    Heated oxygen (HO2) sensor 
    ECM Terminal Names
    Between OX1B and E2
    Tester Ranges
    0.2 V/DIV., 200 msec./DIV.
    Conditions
    Engine speed maintained 2,500 rpm for 2 minutes after warming up sensor

    HINT:
    In the DATA LIST, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.



  20. A093225E07
  21. WAVEFORM 11
    Engine speed signal 
    ECM Terminal Names
    Between TACH and E1
    Tester Range
    5 V/DIV., 10 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as engine rpm increases.