SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST.
According to the display on the tester, use the DATA LIST.
| Intelligent Tester Display | Measurement Item / Range (Display) | Normal Condition* | Diagnostic Note |
| INJECTOR | Injection period of the No. 1 cylinder: Min.: 0 ms, Max.: 32.64 ms | 2.3 to 3.8 ms: idling | - |
| IGN ADVANCE | Ignition timing advance for No. 1 cylinder: Min.: -64 deg., Max.: 63.5 deg. | BTDC 4 to 17°: Idling | - |
| CALC LOAD | Calculated load by ECM: Min.: 0 %, Max.: 100 % |
| - |
| VEHICLE LOAD | Vehicle load: Min.: 0%, Max.: 25700 % | Actual vehicle load | - |
| MAF | Air flow rate from Mass air flow (MAF) meter: Min.: 0 g/sec, Max.: 655 g/sec | 2.0 to 3.9 g/sec: Idling | If the value approximately 0.0 g/sec:
|
| ENGINE SPD | Engine speed: Min.: 0 rpm, Max.: 16,383 rpm | 550 to 650 rpm: Idling | - |
| VEHICLE SPD | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| COOLANT TEMP | Engine coolant temperature: Min.: -40°C, Max.: 140°C | 80 to 100°C (176 to 212°F): After warming up | If the value -40°C (-40°F): sensor circuit open If the value 140°C (284°F): sensor circuit shorted |
| INTAKE AIR | Intake air temperature: Min.: -40°C, Max.: 140°C | Equivalent to ambient air temperature | If the value -40°C (-40°F): sensor circuit open If the value 140°C (284°F): sensor circuit shorted |
| SECONDARY AIR | Second air system status: ON or OFF | ON: Second air system operation | - |
| AIR-FUEL RATIO | Air fuel ratio: Min.: 0, Max.: 1.999 | 0.8 to 1.2: During idling | - |
| EVAP VAPOR PRES | EVAP vapor pressure: Min.: -8192 Pa, Max.: 8191 Pa | 0 Pa: Fuel tank cap removed | - |
| PURGE DENSITY | Learning value of purge density: Min.: -50, Max.: 350 | Idling: -40 to 0 % | Service data |
| PURGE FLOW | Purge flow: Min.: 0 %, Max.: 102.4 % | 0 to 100 %: Idling | - |
| EVAP PURGE VSV | Purge VSV control duty: Min.: 0 %, Max.: 100 % | 0 to 100 %: During idling | Order signal from ECM |
| VAPOR PRESS | Vapor pressure: Min.: -4.125 kPa, Max.: 2.125 kPa | 0 KPa: Fuel tank cap removed | Pressure inside fuel tank monitored by vapor pressure sensor |
| KNOCK CRRT VAL | Correction learning value of knocking: Min.: -64 CA, Max.: 1984 CA | 0 to 22° CA: Driving, 70 km/h (44 mph) | Service data |
| KNOCK FB VAL | Feedback value of knocking: Min.: -64 CA, Max.: 1984 CA | -22 to 0° CA: Driving, 70 km/h (44 mph) | Service data |
| ACCEL POS #1 | Absolute Accelerator Pedal Position (APP) No. 1: Min.: 0%, Max.: 100 % | 10 to 22 %: accelerator pedal is released 54 to 86 %: accelerator pedal is fully depressed | - |
| ACCEL POS #2 | Absolute APP No. 2: Min.: 0 %, Max.: 100 % | 12 to 42 %: accelerator pedal is released 66 to 98 %: accelerator pedal is fully depressed | - |
| ACCEL POS #1 | APP sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| ACCEL POS #2 | APP sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| ACCEL POS #1 | APP sensor No. 1 voltage: Min.: 0 V, Max.: 5 V | 0.5 to 1.1 V: accelerator pedal is released 2.6 to 4.5 V: or pedal is fully depressed | - |
| ACCEL POS #2 | APP sensor No. 2 voltage: Min.: 0 V, Max.: 5 V | 1.2 to 2.0 V: accelerator pedal is released 3.4 to 5.3 V: accelerator pedal is fully depressed | - |
| ACCEL IDL POS | Whether or not accelerator pedal position sensor detecting idle: ON or OFF | ON: Idling | - |
| THRTL LEARN VAL | Throttle valve fully closed (learned value) | 0.4 to 0.8 V | - |
| ACCEL SSR #1 AD | Accelerator fully closed value No. 1 (AD): Min.: 0, Max.: 4.98 V | - | ETCS service data |
| ACCEL LRN VAL#1 | Accelerator fully closed learning value No. 1: Min.: 0, Max.: 124.512 | - | ETCS service data |
| ACCEL LRN VAL#2 | Accelerator fully closed learning value No. 2: Min.: 0, Max.: 124.512 | - | ETCS service data |
| FAIL #1 | Whether or not fail-safe function executed: ON or OFF | ON: ETCS has failed | - |
| FAIL #2 | Whether or not fail-safe function executed: ON or OFF | ON: ETCS has failed | - |
| ST1 | Stater signal: ON or OFF | ON: Cranking | - |
| SYS GUARD JUDGE | System guard: ON or OFF | - | ETCS service data |
| OPN MALFUNCTION | Open side malfunction: ON or OFF | - | ETCS service data |
| THROTTLE POS | Absolute throttle position sensor: Min.: 0 %, Max.: 100 % |
| Read the value with intrusive operation (Active Test) |
| THROTTLE IDL POS | Whether or not throttle position sensor detecting idle: ON or OFF | ON: Idling | - |
| THROTTLE REQ POS | Throttle requirement position: Min.: 0 V, Max.: 5 V | 0.5 to 1.0 V: Idling | - |
| THROTTLE POS | Throttle sensor positioning: Min.: 0 %, Max.: 100 % | 10 to 18 %: Idling | Calculated value based on VTA1 |
| THROTTLE POS #2 | Throttle sensor positioning #2: Min.: 0 %, Max.: 100 % | - | Calculated value based on VTA2 |
| THROTTLE POS #1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.9 V | - | ETCS freeze data |
| THROTTLE POS #2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.9 V | - | ETCS freeze data |
| THROTTLE POS #1 | Throttle position No. 1: Min.: 0 V, Max.: 5 V |
| - |
| THROTTLE POS #2 | Throttle position No. 2: Min.: 0 V, Max.: 5 V |
| Read the value with intrusive operation (Active Test) |
| THRTL COMND VAL | Throttle position command value: Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | ETCS service data |
| THROTTLE SSR #1 | Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | ETCS service data |
| THROTTLE SSR #2 | Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.98 V | 2.2 to 2.6 V | ETCS service data |
| THRTL SSR #1 AD | Throttle sensor opener position No. 1 (AD): Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | ETCS service data |
| THROTTLE MOT | Whether or not throttle actuator control permitted: ON or OFF | ON: Idling | Read the value with the ignition switch ON (Do not start engine) |
| THROTTLE MOT | Throttle actuator current: Min.: 0 A, Max.: 80 A | 0 to 3.0 A: Idling | - |
| THROTTLE MOT | Throttle actuator: Min.: 0 %, Max.: 100 % | 0.5 to 40 %: Idling | - |
| THROTTLE MOT | Throttle actuator current: Min.: 0 A, Max.: 19.92 A | 0 to 3.0 A: Idling | - |
| THROTL OPN DUTY | Throttle actuator opening duty ratio: Min.: 0 %, Max.: 100 % | 0 to 40 %: During idling | When accelerator pedal depressed, duty ratio increased |
| THROTL CLS DUTY | Throttle actuator closed duty ratio: Min.: 0 %, Max.: 100 % | 0 to 40 %: During idling | When accelerator pedal released quickly, duty ratio increased |
| THRTL MOT (OPN) | Throttle actuator duty ratio (open): Min.: 0 %, Max.: 100 % | - | ETCS service data |
| THRTL MOT (CLS) | Throttle actuator duty ratio (close): Min.: 0 %, Max.: 100 % | - | ETCS service data |
| O2S B1 S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 44 mph (70 km/h) | Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor |
| O2S B2 S2 | Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 44 mph (70 km/h) | Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor |
| AFS B1 S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor |
| AFS B2 S1 | Air fuel ratio sensor output voltage for bank 2 sensor 1: Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the INJ VOL or A/F CONTROL function of the ACTIVE TEST enables the technician to check voltage output of the sensor |
| TOTAL FT #1 | Total fuel trim of bank 1 Average value for fuel trim system of bank 1: Min.: -0.5 V, Max.: 1496 V | -0.2 to 0.2: idling | - |
| TOTAL FT #2 | Total fuel trim of bank 2 Average value for fuel trim system of bank 2: Min.: -0.5 V, Max.: 1496 V | -0.2 to 0.2: idling | - |
| SHORT FT #1 | Short-term fuel trim of bank 1: Min.: -100 %, Max.: 99.2 % | -20 to +20 % | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio |
| SHORT FT #2 | Short-term fuel trim of bank 2: Min.: -100 %, Max.: 99.2 % | -20 to +20 % | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio |
| LONG FT #1 | Long-term fuel trim of bank 1: Min.: -100 %, Max.: 99.2 % | -20 to +20 % | This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value |
| LONG FT #2 | Long-term fuel trim of bank 2: Min.: -100 %, Max.: 99.2 % | -20 to +20 % | This item refers to the overall fuel compensation carried out in long-term to compensate a continual deviation of the short-term fuel trim from the central value |
| FUEL SYS #1 | Fuel system status (bank 1): OL, CL, OL DRIVE, OL FAULT or CL FAULT | CL: Idling after warming up |
|
| FUEL SYS #2 | Fuel system status (bank 2): OL, CL, OL DRIVE, OL FAULT or CL FAULT | CL: Idling after warming up |
|
| O2 FT B1 S2 | Short-term fuel trim associated with the bank 1 sensor 2: Min.: -100 %, Max.: 99.2 % | -20 to +20 % | Same as SHORT FT #1 |
| O2 FT B2 S2 | Short-term fuel trim associated with the bank 2 sensor 2: Min.: -100 %, Max.: 99.2 % | -20 to +20 % | Same as SHORT FT #1 |
| AF FT B1 S1 | Short-term fuel trim associated with the bank 1 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| AF FT B2 S1 | Short-term fuel trim associated with the bank 2 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| CAT TEMP B1S1 | Catalyst temperature (bank 1, sensor 1): Min.: -40°C, Max.: 6,513.5°C | - | - |
| CAT TEMP B2S1 | Catalyst temperature (bank 2, sensor 1): Min.: -40°C, Max.: 6,513.5°C | - | - |
| CAT TEMP B1S2 | Catalyst temperature (bank 1, sensor 2): Min.: -40, Max.: 6,513.5°C | - | - |
| CAT TEMP B2S2 | Catalyst temperature (bank 2, sensor 2): Min.: -40, Max.: 6,513.5°C | - | - |
| INI COOL TEMP | Initial engine coolant temperature: Min.: -40°C , Max.: 140°C | Close to ambient air temperature | Service data |
| INI INTAKE TEMP | Initial intake air temperature: Min.: -40°C , Max.: 140°C | Close to ambient air temperature | Service data |
| INJ VOL | Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.048 ml | 0 to 0.5 ml | Quantity of fuel injection volume for 10 times |
| STARTER SIG | Starter signal: ON or OFF | ON: Cranking | - |
| PS SW | Power steering signal: ON or OFF | ON: Power steering operation | - |
| PS SIGNAL | Power steering signal: ON or OFF | ON: When steering wheel first turned after ignition switch turned ON | This signal status usually ON until ignition switch turned OFF |
| CTP SW | Closed throttle position switch: ON or OFF |
| - |
| A/C SIGNAL | A/C signal: ON or OFF | ON: A/C ON | - |
| ELECT LOAD SIG | Electrical load signal: ON or OFF | ON: Headlights or defogger is turned ON | - |
| STOP LIGHT SW | Stop light switch: ON or OFF | ON: Brake pedal is depressed. | - |
| +BM | Whether or not electric throttle control system power inputted: ON or OFF | ON: Idling | - |
| +BM VOLTAGE | +BM voltage: Min.: 0, Max.: 19.92 | 10 to 15 V: Idling | ETCS service data |
| BATTERY VOLTAGE | Battery voltage: Min.: 0 V, Max.: 65,535 V | 9 to 14 V: Idling | - |
| ACTUATOR POWER | Actuator power supply: ON or OFF | ON: Idling | ETCS service data |
| ATM PRESSURE | Atmospheric pressure: Min.: 0 kPa, Max.: 150 kPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| SECOND AIR VSV | Secondary air injection system status | ON: Secondary air injection system operation | - |
| ACT VSV | A/C cut status for Active Test: ON or OFF | - | Active Test support data |
| EVAP (Purge) VSV | VSV status for EVAP control: ON or OFF | - | Active Test support data |
| FUEL PUMP / SPD | Fuel pump/speed status: ON or OFF | - | Active Test support data |
| VVT CTRL B1 | Variable valve timing (VVT) control status (bank 1): ON or OFF | - | Active Test support data |
| VVT CTRL B2 | VVT control status (bank 2): ON or OFF | - | Active Test support data |
| VACUUM PUMP | Key-off EVAP system pump status: ON or OFF | - | Active Test support data |
| EVAP VENT VAL | Key-off EVAP system vent valve status: ON or OFF | - | Active Test support data |
| TC/TE1 | TC and TE1 terminal of DLC3: ON or OFF | - | - |
| VVTL AIM ANGL #1 | VVT aim angle (bank 1): Min.: 0 %, Max.: 100 % | 0 %: Idling | VVT duty signal value during intrusive operation |
| VVTL AIM ANGL #2 | VVT aim angle (bank 2): Min.: 0 %, Max.: 100 % | 0 %: Idling | VVT duty signal value during intrusive operation |
| VVTL CHAG ANGL #1 | VVT change angle (bank 1): Min.: 0° FR , Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation |
| VVT CHNG ANGL #2 | VVT change angle (bank 2): Min.: 0° FR , Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation |
| VVT OCV DUTY B1 | VVT OCV operation duty (bank 1): Min.: 0 %, Max.: 100 % | 0 %: Idling | Requested duty value for intrusive operation |
| VVT OCV DUTY B2 | VVT OCV operation duty (bank 2): Min.: 0 %, Max.: 100 % | 0 %: Idling | Requested duty value for intrusive operation |
| FC IDL | Fuel cut idle: ON or OFF | ON: Fuel cut operation | FC IDL = "ON" when throttle valve fully closed and engine speed over 2800 rpm |
| FC TAU | Fuel cut TAU: Fuel cut during very light load: ON or OFF | ON: Fuel cut operation | The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete |
| IGNITION | Ignition counter: Min.: 0, Max.: 800 | 0 to 800 | - |
| CYL #1, #2, #3, #4, #5, #6, #7, #8 | Misfire ratio of the cylinder 1 to 8: Min.: 0, Max.: 255 | 0 % | This item displayed only when idling engine |
| CYL ALL | All cylinders misfire rate: Min.: 0, Max.: 255 | 0 to 35 | - |
| MISFIRE RPM | Engine RPM for first misfire range: Min.: 0 rpm, Max.: 6,375 rpm | 0 rpm: Misfire 0 | - |
| MISFIRE LOAD | Engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| MISFIRE MARGIN | Misfire monitoring: Min.: -100 %, Max.: 99.22 % | -100 to 99.2 % | Misfire detecting margin |
| #CODES | #Codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| CHECK MODE | Check mode: 0: ON, 1: OFF | ON: Check mode ON | Click here
|
| SPD TEST | Check mode result for vehicle speed sensor: 0: COMPL, 1: INCOMPL | - | - |
| AS TEST | Check mode result for secondary air injection system: 0: COMPL, 1: INCOMPL | - | - |
| MISFIRE TEST | Check mode result for misfire monitor: 0: COMPL, 1: INCOMPL | - | - |
| OXS1 TEST | Check mode result for heated oxygen sensor (bank 1): 0: COMPL, 1: INCOMPL | - | - |
| OXS2 TEST | Check mode result for heated oxygen sensor (bank 2): 0: COMPL, 1: INCOMPL | - | - |
| A/F SSR TEST B1 | Check mode result for air fuel ratio sensor (bank 1): 0: COMPL, 1: INCOMPL | - | - |
| A/F SSR TEST B2 | Check mode result for air fuel ratio sensor (bank 2): 0: COMPL, 1: INCOMPL | - | - |
| MIL | MIL status: ON or OFF | ON: MIL ON | - |
| MIL ON RUN DIST | MIL ON run distance: Min.: 0 km, Max.: 65,535 km | Distance after DTC detected | - |
| MIL ON RUN TIME | Running time from MIL ON: Min.: 0 minute, Max.: 65,535 minutes | Equivalent to running time after MIL was ON | - |
| ENG RUN TIME | Engine run time: Min.: 0 seconds, Max.: 65,535 seconds | Time after engine start | Service data |
| TIME DTC CLEAR | Time after DTC cleared: Min.: 0 minutes, Max.: 65,535 minutes | Equivalent to time after DTCs were erased | - |
| DIST DTC CLEAR | Distance after DTC cleared: Min.: 0 km, Max.: 65,535 km | Equivalent to drive distance after DTCs were erased | - |
| WU CYC DTC CLEAR | Warm-up cycle after DTC cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| MODEL CODE | Model code | - | Identifying the model code: UCK30 (2WD), UCK40 (4WD) |
| ENGINE TYPE | Engine type | - | Identifying the engine type: 2UZFE |
| CYLINDER NUMBER | Cylinder number: Min.: 0, Max.: 255 | - | Identifying the cylinder number: 8 |
| TRANSMISSION | Transmission type | - | Identifying the transmission type: ECT (5AT) |
| DESTINATION | Destination | - | Identifying the destination: A (America) |
| MODEL YEAR | Model year: Min.: 0, Max.: 255 | - | Identifying the model year: 200# |
| SYSTEM | System identification | - | Identifying the engine system: GASLIN (gasoline engine) |
| AI STATUS | AI operation prohibit: OK or NG | OK | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.
According to the display on the tester, perform the ACTIVE TEST.
| Intelligent Tester Display | Test Details | Control Range | Diagnostic Note |
| INJ VOL | Change injection volume | Between -12 % and 25 % |
|
| A/F CONTROL | Change injection volume | Lower by 12.5 % or increase 25 % |
|
| EVAP VSV (ALONE) | Activate purge VSV control | ON/OFF | - |
| VVT CTRL B1 | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| VVT CTRL B2 | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| AC CUT SIG | Control A/C cut signal | ON/OFF | - |
| FUEL PUMP / SPD | Activate fuel pump (C/OPN Relay) | ON/OFF | - |
| TC/TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| FC IDL PROHBT | Prohibit idling fuel cut control | ON/OFF | - |
| ETCS OPEN SLOW | Throttle actuator | ON: throttle valve opens slowly | This test is possible when the following conditions are met:
|
| ETCS CLOSE SLOW | Throttle actuator | ON: throttle valve closes slowly | Same as above |
| ETCS OPEN FAST | Throttle actuator | ON: throttle valve opens fast | Same as above |
| ETCS CLOSE FAST | Throttle actuator | ON: throttle valve closes fast | Same as above |
| FUEL CUT #1 | Cylinder #1 injector fuel cut | ON/OFF | This test is possible when the vehicle is stopped and the engine is idling. |
| FUEL CUT #2 | Cylinder #2 injector fuel cut | ON/OFF | Same as above |
| FUEL CUT #3 | Cylinder #3 injector fuel cut | ON/OFF | Same as above |
| FUEL CUT #4 | Cylinder #4 injector fuel cut | ON/OFF | Same as above |
| FUEL CUT #5 | Cylinder #5 injector fuel cut | ON/OFF | Same as above |
| FUEL CUT #6 | Cylinder #6 injector fuel cut | ON/OFF | Same as above |
| FUEL CUT #7 | Cylinder #7 injector fuel cut | ON/OFF | Same as above |
| FUEL CUT #8 | Cylinder #8 injector fuel cut | ON/OFF | Same as above |
| VENT VALVE (ALONE) | Activate vent valve (built into canister pump module) | ON/OFF | - |
| VACUUM PUMP | Activate vacuum pump (built into canister pump module) | ON/OFF | - |
| SYSTEM CHECK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK.
Perform the SYSTEM CHECK by referring to the table below.
| Intelligent Tester Display | Test Details | Recommended Fuel Temperatures | Diagnostic Notes |
| EVAP SYS CHECK (AUTOMATIC) | Perform 5 steps in order to operate EVAP key-off monitor automatically | 35°C (95°F) or less |
|
| EVAP SYS CHECK (MANUAL) | Perform 5 steps in order to operate EVAP key-off monitor manually | 35°C (95°F) or less |
|
| AIR INJ CHECK (AUTOMATIC) | Perform 6 steps in order to operate air injection system automatically | - | If no DTCs in PENDING CODES menu after performing this test, system functioning normally |
| AI INJ CHECK (MANUAL) | Perform 8 operations in order to operate air injection system monitor manually | - | Used to detect malfunctioning parts |