Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

In addition to turning on the stop lights, the stop light switch signals are used for a variety of engine, transmission and suspension functions. The stop light switch is designed with 2 complementary signal outputs, STP and ST1-. The ECM analyzes these signal outputs to detect malfunctions in the stop light switch.

HINT:
Normal condition is as shown in the table below.


Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
  1. Conditions (a), (b) and (c) continue for 0.5 seconds or more:
    1. (a) Ignition switch ON
    2. (b) Brake pedal released
    3. (c) STP signal is OFF when the ST1- signal is OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch assembly
  4. ECM

WIRING DIAGRAM


A133729E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OPERATION OF STOP LIGHT
  1. Check if the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK :
    Stop light turns ON when brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Check stop light switch .



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3.READ VALUE OF INTELLIGENT TESTER (STP SIGNAL AND ST1- VOLTAGE)


    A112419E05
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / STOP LIGHT SW.

  1. Confirm the stop light switch status when the brake pedal is depressed and released.

    OK:
    Brake Pedal Condition
    Specified Condition
    Depressed
    STP Signal ON
    Released
    STP Signal OFF

  1. Measure the voltage of the ECM when the brake pedal is depressed and released.

    Standard voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    ST1- (E8-16) - E1 (E6-1)
    Depressed
    Below 1.5 V
    ST1- (E8-16) - E1 (E6-1)
    Released
    7.5 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)


    A138065E01
  1. Disconnect the S12 stop light switch connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    Stop light switch (S12-1) - STP (E8-15)
    Below 1 Ω
    Stop light switch (S12-4) - ST1- (E8-16)
    Stop light switch (S12-1) or STP (E8-15) - Body ground
    10 kΩ or higher
    Stop light switch (S12-4) or ST1- (E8-16) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the stop light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM