Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0560    System Voltage

for Preparation Click here


MONITOR DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is OFF. This electricity allows the ECM to store data such as DTC history, freeze frame data, fuel trim values, and other data. If the battery voltage falls below a minimum level, the memory is cleared and the ECM will conclude that there is a fault in the power supply circuit. At the next engine start, the ECM will illuminate the MIL and set a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back-up power source circuit
  1. Open in back-up power source circuit
  2. EFI fuse
  3. ECM

HINT:
If DTC P0560 appears, the ECM does not store another DTC.


MONITOR STRATEGY


Related DTCs
P0560: ECM system voltage
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate (MIL will be illuminated after next engine start)
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
None
Stand-by RAM
Initialized

TYPICAL MALFUNCTION THRESHOLDS


ECM power source
Less than 3.5 V

WIRING DIAGRAM


A074726E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE OF INTELLIGENT TESTER (BATTERY VOLTAGE)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / BATTERY VOLTAGE.

    Result:

    Battery voltage
    Proceed to
    Battery voltage is 0 V
    A
    Battery voltage is except 0 V
    B



B
Go to step 5
A


2.INSPECT FUSE (EFI NO. 1)


    A072881E01
  1. Remove the EFI fuse from the engine room relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK ECM (BATT VOLTAGE)


    A115711E02
  1. Measure the voltage between terminals of the E6 and E8 ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    BATT (E6-3) - E1 (E8-1)
    9 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


4.CHECK HARNESS AND CONNECTOR (ECM - EFI NO. 1 FUSE)


    A138068E01
  1. Check the harness and the connector between the EFI fuse and ECM.

    1. Remove the EFI fuse from the engine room R/B.

    2. Disconnect the E8 ECM connector.

    3. Check the resistance between the wire harness side connectors.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      Engine room R/B (EFI fuse terminal 2) - BATT (E8-3)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      Engine room R/B (EFI fuse terminal 2) or BATT (E8-3) - Body ground
      10 kΩ or higher

    4. Reinstall the EFI fuse.

    5. Reconnect the ECM connector.

  1. Check the harness and the connector between the EFI fuse and battery.

    1. Remove the EFI fuse from the engine room R/B.

    2. Disconnect the negative battery cable.

    3. Check the resistance between the wire harness side connectors.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      Positive battery cable - Engine room R/B (EFI fuse terminal 1)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      Positive battery cable or Engine room R/B (EFI fuse terminal 1) - Body ground
      10 kΩ or higher

    4. Reinstall the EFI fuse.

    5. Reconnect the negative battery cable.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery voltage is 11 V or more.



NG
REPLACE BATTERY
OK

CHECK AND REPLACE ENGINE ROOM RELAY BLOCK