Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

HINT:
While the engine is being cranked, the battery positive voltage is applied to terminal STA of the ECM.

If the vehicle is being driven and the ECM detects the starter control signal (STA), the ECM concludes that the starter control circuit is malfunctioning. The ECM will turn on the MIL and a DTC is set.

DTC No.
DTC Detection Condition
Trouble Area
P0617
The following conditions are met for 20 seconds:
  1. Vehicle speed is greater than 12 mph (20 km/h)
  2. Engine RPM is greater than 1,000 rpm
  3. ECM detects STA
  1. Starter relay circuit
  2. Park/Neutral Position (PNP) switch
  3. Ignition switch
  4. ECM

MONITOR STRATEGY


Related DTCs
P0617: Starter signal error
Required Sensors/Components (Main)
STARTER relay, PNP switch, Ignition switch
Required Sensors/Components (Related)
Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever these DTCs are not present
None
Battery voltage
10.5 V or more
Vehicle speed
12.4 mph (20 km/h) or more
Engine rpm
1,000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Starter signal
ON

WIRING DIAGRAM


A133731E01


INSPECTION PROCEDURE

HINT:
  1. This DTC chart is on the premise that the engine is cranked normally. If the engine is not cranked, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE OF INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / STARTER SIG.

  1. Confirm the starter signal status when the ignition switch is operated.

    OK:

    Ignition Switch Position
    STARTER SIG
    ON
    OFF
    Start
    ON



OK
Go to step 5
NG


2.INSPECT PARK / NEUTRAL POSITION SWITCH


    A093221E12
  1. Move the shift lever to the P or N position.

  1. Disconnect the P1 Park / Neutral Position (PNP) switch connector.

  1. Measure the resistance of the PNP switch.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    Below 1 Ω
    N
    2 - 9, 4 - 5
    Below 1 Ω
    D, 4
    2 - 7
    Below 1 Ω
    3
    2 - 4
    Below 1 Ω
    2, L
    2 - 8
    Below 1 Ω

  1. Reconnect the park / neutral position switch connector.



NG
REPLACE PARK / NEUTRAL POSITION SWITCH (GO TO STEP 5 AFTER THE REPLACEMENT)
OK


3.INSPECT IGNITION SWITCH ASSEMBLY


    A087913E10
  1. Disconnect the I18 ignition switch connector.

  1. Measure the resistance between the connector terminals shown in the chart below.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    2-3
    Below 1 Ω
    ON
    2-3, 2-4, 6-7
    Below 1 Ω
    START
    1-2, 2-4, 6-7, 6-8
    Below 1 Ω

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (GO TO STEP 5 AFTER REPLACEMENT)
OK


4.READ VALUE OF INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. On the intelligent tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / STARTER SIG.

  1. Read the values.

    OK:
    Ignition Switch Position
    STARTER SIG
    ON
    OFF
    START
    ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs.

  1. Drive the vehicle more than 25 mph (40 km/h) for 20 seconds or more.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE ECM