DTC P0335 Crankshaft Position Sensor "A" Circuit |
DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 |
|
|
| P0339 | No CKP sensor signal to ECM is input for 0.05 seconds or more, and conditions (a), (b) and (c) are met: (a) 1,000 rpm or more (b) Starter is OFF (c) 3 seconds or more have elapsed after STA signal is switched from ON or OFF |
|
![]() |
| Tester Connection | Specified Condition |
| VV1+ (E6-25) - VV1- (E6-24) | Correct waveform is as shown |
| VV2+ (E6-18) - VV2- (E6-28) | |
| G2+ (E6-19) - G2- (E6-29) | |
| NE+ (E6-21) - NE- (E67-20) |
| Related DTCs | Crankshaft position sensor range check or rationality |
| Required Sensors/Components | Crankshaft position (CKP) sensor |
| Required Sensors/Components | - |
| Frequency of Operation | Continuous |
| Duration | Case 1: 3 times Case 2: 0.016 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Time after starter OFF to ON | 0.3 seconds or more |
| Number of camshaft position sensor signal pulse | 6 times |
| Battery voltage | 7 V or more |
| Ignition switch | ON |
| CMP sensor circuit fail | Not detected |
| Starter | OFF |
| Engine RPM | 450 rpm or more |
| Time after starter from ON to OFF | 3 seconds or more |
| Number of CKP sensor signal pulse | 132 or less, or 174 or more |
| Engine speed signal | No signal for 0.016 second |

| 1.INSPECT CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the C4 Crankshaft Position (CKP) sensor connector.
Measure the resistance of the sensor.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Cold | 1,630 to 2,740 Ω |
| 1 - 2 | Hot | 2,065 to 3,225 Ω |
Reconnect the crankshaft position sensor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
![]() |
Disconnect the C4 crankshaft position sensor connector.
Disconnect the E6 ECM connector.
Measure the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| Crankshaft position sensor (C1-1) - NE+ (E6-21) | Below 1 Ω |
| Crankshaft position sensor (C4-2) - NE- (E6-20) | |
| Crankshaft position sensor (C1-1) or NE+ (E6-21) - Body ground | 10 kΩ or higher |
| Crankshaft position sensor (C4-2) or NE- (E6-20) - Body ground |
Reconnect the CKP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the sensor installation.
|
| ||||
| OK | |
| 4.CHECK CRANKSHAFT POSITION SENSOR PLATE (TOOTH OF PLATE) |
Remove the crankshaft position sensor plate .
Check the tooth of the signal plate.
|
| ||||
| OK | ||
| ||