DTC P1340 Camshaft Position Sensor "A" (Bank 1 Sensor 2) |
DTC P1341 Camshaft Position Sensor "A" (Bank 1 Sensor 2 ) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1340 P1341 | No camshaft position sensor signal to ECM during cranking (2 trip detection logic) |
|
| No camshaft position sensor signal to ECM with engine speed 600 rpm or more |
| Related DTCs | P1340: Camshaft position sensor range check P1340: Camshaft position / Crankshaft position misalignment P1341: Camshaft position sensor malfunction |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, Engine speed sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | 2 driving cycles: Camshaft position sensor range check Immediate: Camshaft position / Crankshaft position misalignment and camshaft position sensor malfunction |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Starter | ON |
| Minimal battery voltage while starter ON | Less than 11 V |
| Engine RPM | 600 rpm or more |
| Starter | OFF |
| Starter | After OFF to ON timing |
| Camshaft position signal | No signal |
| Camshaft position and crankshaft position phase | Misaligned |
| Camshaft position and crankshaft position phase | Misaligned |
| Camshaft position signal per 2 revolutions of crankshaft | 12 signals or more |
| Camshaft position sensor signal |
|
| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the C1 camshaft position sensor connector.
Turn the ignition switch ON.
Measure the voltage between terminal 3 of the camshaft position sensor connector and body ground.
| Tester Connection | Specified Condition |
| C1-3 - Body ground | 4.5 to 5.0 V |
Reconnect the camshaft position sensor connector.
|
| ||||
| OK | |
| 2.CHECK ECM TERMINAL VOLTAGE |
![]() |
Inspect the ECM using an oscilloscope.
While the engine is idling, check the waveform between the terminals of the ECM connector.
| Tester Connection | Specified Condition |
| G2+ (E6-19) - G2- (E6-29) | Correct waveform is as shown |
|
| ||||
| NG | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR) |
![]() |
Disconnect the C1 Camshaft position sensor connector.
Disconnect the E6 ECM connector.
Measure the resistance between wire harness side connectors.
| Tester Connection | Specified Condition |
| Camshaft position sensor (C1-2) - G2+ (E6-19) | Below 1 Ω |
| Camshaft position senssor (C1-1) - G2- (E6-29) | |
| Camshaft position sensor (C1-2) or G2+ (E6-19) - Body ground | 10 kΩ or higher |
| Camshaft position sensor (C1-1) or G2- (E6-29) - Body ground |
Reconnect the ECM connector.
Reconnect the Camshaft position sensor connector.
|
| ||||
| OK | |
| 4.INSPECT SENSOR INSTALLATION |
![]() |
Check the camshaft position sensor installation.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING PULLEY LH (SIGNAL PLATE TOOTH) |
|
| ||||
| OK | ||
| ||