Home › ENGINE ยท 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0101    Mass Air Flow Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTCs P0100 .

DTC No.
DTC Detection Condition
Trouble Area
P0101
(1) After the engine is warmed up, conditions (a), (b), (c) and (d) continue for more than 10 seconds (2 trip detection logic):
(a) Throttle valve is fully closed
(b) Voltage output of the mass air flow meter is more than 2.2 V
(c) Engine coolant temperature is more than 70°C
(d) Engine speed is less than 900 rpm
(2) Conditions (a), (b) and (c) continue for more than 6 seconds (2 trip detection logic):
(a) Engine speed is more than 0 rpm
(b) VTA is more than 0.1 V
(c) Voltage output of the mass air flow meter is less than 0.25 V
Mass air flow meter

MONITOR DESCRIPTION

The Mass Air Flow (MAF) meter helps the ECM calculate the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provide a proper air fuel ratio. Inside the MAF meter, there is a heated platinum wire exposed to the flow of intake air. By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the air flow through the sensor. The ECM interprets this voltage as the intake air amount. If there is a defect in the sensor or an open or short circuit, the voltage level will deviate outside the normal operating range. The ECM interprets this deviation as a defect in the MAF meter and sets a DTC.
Example:
If the MAF meter voltage is higher than 2.2 V when the engine is idling, the ECM sets P0101 (2 trip detection logic). If the MAF meter voltage is less than 1.0 V when the throttle valve is open, the ECM sets DTC P0101 (2 trip detection logic).

MONITOR STRATEGY


Related DTCs
P0101: MAF Meter Rationality (low voltage)
P0101: MAF Meter Rationality (high voltage)
Required Sensors/Components (Main)
MAF meter
Required Sensors/Components (Related)
Engine speed sensor, Engine coolant temperature sensor, Throttle position sensor
Frequency of Operation
Continuous
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


ALL: 
Monitor will run whenever these DTCs are not present
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (insufficient ECT for closed loop)
P0335 (CKP sensor)

Mass air flow meter rationality (high voltage) 
Engine speed
Less than 2,000 rpm
Engine coolant temperature
70°C (158°F) or more

Mass air flow meter rationality (low voltage) 
Engine speed
More than 300 rpm
Fuel cut
OFF

TYPICAL MALFUNCTION THRESHOLDS


Mass air flow meter rationality (high voltage) 
Mass air flow meter voltage
More than 2.2 V (varies with throttle position sensor voltage)

Mass air flow meter rationality (low voltage) 
Mass air flow meter voltage
Less than 1.0 V (varies with throttle position sensor voltage)

WIRING DIAGRAM

Refer to DTCs P0100 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)
  1. Connect the intelligent tester to the DLC3 with the CAN VIM.

  1. Turn the ignition switch ON and tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0101 and other codes are output
    A
    Only P0101 is output
    B

    HINT:
    If any other codes besides P0101 are output, perform troubleshooting for those DTCs first.



B
REPLACE MASS AIR FLOW METER
A

GO TO RELEVANT DTC CHART