DTC P0110 Intake Air Temperature Circuit |
DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |
![]() |
| DTC No. | Proceed to | DTC Detection Condition | Trouble Area |
| P0110 | Step 1 | Open or short in IAT sensor circuit for 0.5 seconds |
|
| P0112 | Step 4 | Short in IAT sensor circuit for 0.5 seconds |
|
| P0113 | Step 2 | Open in IAT sensor circuit for 0.5 seconds |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) | Short circuit |
| Related DTCs | P0110: IAT sensor range check (fluttering) P0112: IAT sensor range check (low resistance) P0113: IAT sensor range check (high resistance) |
| Required Sensors/Components (Main) | IAT sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor will run whenever these DTCs are not present | None |
| The typical enabling condition is not available | - |
| IAT sensor voltage [Intake air temperature] | Less than 0.18 V, or more than 4.91 V (More than 140°C (284°F), or less than -40°C (-40°F)) |
| IAT sensor voltage [Intake air temperature] | Less than 0.18 V (More than 140°C (284°F)) |
| IAT sensor voltage [Intake air temperature] | More than 4.91 V (Less than -40°C (-40°F)) |
| IAT sensor resistance [IAT] | 0.18 V (140°C (284°F)) to 4.91 V (-40°C (-40°F)) |

| 1.READ VALUE OF INTELLIGENT TESTER (INTAKE AIR TEMPERATURE) |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / INTAKE AIR.
Read the values.
| Intake Air Temperature | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or more | B |
| OK (same as present temperature) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the M1 Mass Air Flow (MAF) meter connector.
Connect terminals THA and E2 of the MAF meter wire harness side connector.
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / INTAKE AIR.
Read the value.
Reconnect the MAF meter connector.
|
| ||||
| NG | |
| 3.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN ECM) |
![]() |
Disconnect the M1 MAF meter connector.
Connect terminals THA and E2 of the E4 ECM connector.
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / INTAKE AIR.
Read the value.
Reconnect the MAF meter connector.
|
| ||||
| OK | ||
| ||
| 4.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the M1 MAF meter connector.
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / INTAKE AIR.
Read the value.
Reconnect the MAF meter connector.
|
| ||||
| NG | |
| 5.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN ECM) |
![]() |
Disconnect the M1 MAF meter connector.
Disconnect the E4 ECM connector.
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / INTAKE AIR.
Read the value.
Reconnect the ECM connector.
Reconnect the MAF meter connector.
|
| ||||
| OK | ||
| ||