Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

DTC    P0020    Camshaft Position "A" Actuator Circuit (Bank 2)

for Preparation Click here


DESCRIPTION

HINT:
These DTCs relate to the Oil Control Valve (OCV).

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as intake air volume, throttle valve position and engine coolant temperature.
The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A117755E01


DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in Oil Control Valve (OCV) (bank 1) circuit
(1 trip detection logic)
  1. Open or short in Oil Control Valve (OCV) (bank 1) circuit
  2. Oil Control Valve (OCV) (bank 1)
  3. ECM
P0020
Open or short in OCV (bank 2) circuit
(1 trip detection logic)
  1. Open or short in OCV (bank 2) circuit
  2. OCV (bank 2)
  3. ECM

MONITOR DESCRIPTION

After the ECM sends the "target" duty-cycle signal to the OCV (Oil Control Valve), the ECM monitors the OCV current to establish an "actual" duty-cycle. When the actual duty-cycle ratio varies from the target duty-cycle, the ECM sets a DTC.

MONITOR STRATEGY


Related DTCs
P0010: OCV (bank 1) range check
P0020: OCV (bank 2) range check
Required Sensors/Components (Main)
VVT OCV
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
None
Starter
OFF
Ignition switch
ON
Time after ignition switch OFF to ON
0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


One of the following conditions is met
Condition A, B or C
A. All of the following conditions are met
Condition (a), (b) and (c)
a. Battery voltage
11 V or more, and less than 13 V
b. Target duty ratio
Less than 70 %
c. Output signal duty ratio
100 % or more
B. All of the following conditions are met
Condition (a), (b) and (c)
a. Battery voltage
13 V or more
b. Target duty ratio
Less than 80 %
c. Output signal duty ratio
100 % or more
C. Both of the following conditions are met
Condition (a) and (b)
a. Current cut status
Not cut
b. Output signal duty ratio
3 % or less

COMPONENT OPERATING RANGE


Output signal duty for OCV
More than 3 %, and less than 100 %

WIRING DIAGRAM


A115908E02


INSPECTION PROCEDURE

HINT:
  1. If DTC P0010 is displayed, check the bank 1 VVT system circuit.
  2. Bank 1 refers to the bank that includes cylinder No. 1.
  3. If DTC P0020 is displayed, check the bank 2 VVT system circuit.
  4. Bank 2 refers to the bank that does not include cylinder No. 1.
  5. Read freeze frame data using a intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (OCV OPERATION)
  1. Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.

  1. Start the engine and warm it up.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1 or VVT CTRL B2.

  1. Operate the Oil Control Valve (OCV) and check the engine condition at idling.

    OK:

    Tester Operation
    Specified Condition
    OCV is OFF
    Normal engine speed
    OCV is ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OPERATION)


    A088857E03
  1. Disconnect the C13 or C14 OCV connectors.

  1. Apply battery voltage to the terminals of the OCV.

  1. Check the engine speed.

    OK:
    Rough idle or engine stalled.

  1. Reconnect the OCV connectors.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
OK


3.CHECK ECM (OCV SIGNAL)


    G035623E04
  1. Inspect the ECM using an oscilloscope.

  1. While idling the engine, check the waveform of the E6 ECM connector using an oscilloscope.

    Standard voltage:
    Tester Connection
    Specified Condition
    OC1+ (E6-17) - OC1- (E6-16)
    Correct waveform is as shown
    OC2+ (E6-15) - OC2- (E6-14)



NG
REPLACE ECM
OK


4.CHECK HARNESS AND CONNECTOR (OCV - ECM)


    A115689E02
  1. Disconnect the C2 or C3 OCV connectors.

  1. Disconnect the E6 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified condition
    OCV (C2-1) - OC1+ (E6-17)
    Below 1 Ω
    OCV (C2-2) - OC1- (E6-16)
    OCV (C3-1) - OC2+ (E6-15)
    OCV (C3-2) - OC2- (E6-14)

    Standard resistance (Check for short):
    Tester Connection
    Specified condition
    OCV (C2-1) or OC1+ (E6-17) - Body ground
    10 kΩ or higher
    OCV (C2-2) or OC1- (E6-16) - Body ground
    OCV (C3-1) or OC2+ (E6-15) - Body ground
    OCV (C3-2) or OC2- (E6-14) - Body ground

  1. Reconnect the OCV connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS