Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)

AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / DATA LIST".

  7. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item/Range (display)
    Normal Condition
    Diagnostic Note
    STOP LIGHT SW
    Stop light switch Status/ON or OFF
    1. Brake Pedal is depressed: ON
    2. Brake Pedal is released: OFF
    -
    PNP SW [NSW]
    PNP switch Status/ON or OFF
    Shift lever position is;
    P and N: ON
    Except P and N: OFF
    When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    LOW
    PNP switch Status/ON or OFF
    Shift lever position is;
    L: ON
    Except L: OFF
    ↑
    2ND
    PNP switch Status/ON or OFF
    Shift lever position is;
    2 and L: ON
    Except 2 and L: OFF
    ↑
    3RD
    PNP SW Status/ON or OFF
    Shift lever position is;
    3: ON
    Except 3: OFF
    ↑
    4th/DRIVE
    PNP SW Status/ON or OFF
    Shift lever position is;
    4: ON
    Except 4: OFF
    ↑
    REVERSE
    PNP switch Status/ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    ↑
    DRIVE
    PNP switch Status/ON or OFF
    Shift lever position is;
    D and 4: ON
    Except D and 4: OFF
    ↑
    SHIFT
    Actual Gear Position/1st, 2nd, 3rd, 4th or 5th
    Shift lever position is;
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. 4: 1st, 2nd, 3rd or 4th
    5. D: 1st, 2nd, 3rd, 4th or 5th
    -
    LOCK UP SOL
    Lock Up Solenoid Status/ON or OFF
    1. Lock Up: ON
    2. Except Lock Up: OFF
    -
    SOLENOID (SLT)
    Shift Solenoid SLT Status/ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    SOLENOID (SLU)
    Shift Solenoid SLU Status/ON or OFF
    1. Lock Up: ON
    2. Except Lock Up: OFF
    -
    AT FLUID TEMP
    ATF Temp. Sensor No. 1 Value/min.: -40°C (-40°F) max.: 215°C (419°F)
    1. After Stall Test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor No. 1 circuit is opened or shorted.
    AT FLUID TEMP 2
    ATF Temp. Sensor No.2 Value/min.: -40°C (-40°F) max.: 215°C (419°F)
    1. After Stall Test; Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor No. 2 circuit is open or shorted.
    SPD (SP2)
    Output shaft Speed/min.: 0 km/h (0 mph) max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)

    HINT:
    Equal to vehicle speed

    -
    SPD (NT)
    Input Turbine Speed/display: 50 r/min

    HINT:
    1. Lock-up ON (After warming up the engine):
      Input Turbine speed (NT) equal to the engine speed.
    2. Lock-up OFF (Idling at N position):
      Input Turbine speed (NT) nearly equal to the engine speed.

    -


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
If is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Push the "ON" button of the intelligent tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST".

  7. According to the display on tester, perform the "ACTIVE TEST".

    Item
    Test Details
    Diagnostic Note
    SHIFT
    [Test Details]
    Operate the shift solenoid valve and set the each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check the operation of the shift solenoid valves.
    LOCK UP
    [Test Details]
    Control the shift solenoid SLU to set the automatic transmission to the lock-up condition.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle Speed: 60 km/h (37 mph) or more
    Possible to check the SLU operation.
    LINE PRESS UP *
    [Test Details]
    Operate the shift solenoid SLT and raise the line pressure.
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. IDL: ON
    [HINT]
    OFF: Line pressure up (When the active test of "Control the Line Pressure Up" is performed, the ECM commands the SLT solenoid to turn off).
    ON: No action (normal operation)
    -
    *: "LINE PRESS UP" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.