Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)

DTC    P0717    Turbine Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of transmission. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. Thus, providing smooth gear shift.

G036793E03


DTC No.
DTC Detection Condition
Trouble Area
P0717
All conditions below are detected for 5 secs. or more (1-trip detection logic)
(a) Gear change is not performed
(b) Gear position: 4th or 5th
(c) T/M input shaft rpm: 300 rpm or less
(d) T/M output shaft rpm: 1,000 rpm or more
(e) Park/neutral position switch:
  1. NSW input signal is OFF
  2. R input signal is OFF
  3. L input signal is OFF
(f) Shift solenoid valves and park/neutral position switch are in normal operation
  1. Open or short in speed sensor (NT) circuit
  2. Speed sensor (NT)
  3. ECM
  4. Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between the terminals NT+ and NT- of the ECM connector.
G020663E06

Standard:
Refer to the illustration.

Terminal
NT+ - NT-
Tool setting
1 V/DIV, 2 ms./DIV.
Vehicle condition
Engine idle speed (P or N position)

MONITOR DESCRIPTION

This DTC indicates that pulse is not output from the speed sensor NT (Turbine (input) speed sensor) or is output only little. The NT terminal of the ECM detects the revolving signal from speed sensor (NT) (input RPM). The ECM outputs a gearshift signal comparing the input speed sensor (NT) with the output speed sensor (SP2).
While the vehicle is operating in the 4th or 5th gear position in the shift position of D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1,000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is approx. 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components (Main)
Speed sensor (NT)
Required sensors/Components (Related)
Speed sensor (NC)
Frequency of operation
Continuous
Duration
5 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
P0500 (VSS)
P0748 (Trans solenoid (range))
Shift change
Shift change is completed and before starting next shift change operation
ECM selected gear
4th or 6th
Output shaft rpm
1,000 rpm or more
NSW (STAR) switch
OFF
R switch
OFF
L switch
OFF
Engine
Running
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Sensor signal rpm
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor (NT)
Input speed is equal to engine speed when lock-up ON.

WIRING DIAGRAM


G031763E50


INSPECTION PROCEDURE


DATA LIST

HINT:
According to the DATA LIST displayed by the intelligent tester, you can read the value of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of troubleshooting is one method to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / DATA LIST".

  7. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item/Range (display)
    Normal Condition
    SPD (NT)
    Input Turbine Speed/display: 50 r/min

    HINT:
    1. Lock-up ON (After warming up the engine);
      Input Turbine speed (NT) equal to the engine speed.
    2. Lock-up OFF (Idling at N position);
      Input Turbine speed (NT) nearly equal to the engine speed.

    HINT:
    1. SPD (NT) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR INSTALLATION


    BR03795E43
  1. Check the speed sensor (NT) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL SPEED SENSOR OR REPLACE SPEED SENSOR
OK


2.INSPECT SPEED SENSOR (NT)


    C110343E42
  1. Disconnect the speed sensor connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (NT)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM)


    G035616E80
  1. Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    E5-35 (NT+) - E5-27 (NT-)
    560 to 680 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    E5-35 (NT+) - Body ground
    10 kΩ or higher
    E5-27 (NT-) - Body ground
    ↑



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM