Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


SYSTEM DESCRIPTION

The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the duty ratio (*) of the SLT solenoid valve to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle. For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then
Duty Ratio = A/(A+B) x 100 (%)
C108924E02

DTC No.
DTC Detection Condition
Trouble Area
P2714
ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the output shaft, and also by the oil pressure. (2-trip detection logic)
  1. Shift solenoid valve SLT remains open or closed
  2. Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed
  3. Gear 6 incorrect ratio (reverse sequence valve) or 1-2 shift valve is stuck
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and outputs this DTC when the amount of heat absorption exceeds the specified value.
When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.

NOTICE:
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


MONITOR STRATEGY


Related DTCs
P2714: Shift solenoid valve SLT/ON malfunction
Required sensors/Components
Shift solenoid valve SLT, Valve body, ATF temperature sensor, Speed sensor (NT), Speed sensor (NO)
Frequency of operation
Continuous
Duration
Immediate
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
None
Turbine speed sensor (NT) circuit
Not circuit malfunction
Output speed sensor (NO) circuit
Not circuit malfunction
TFT temperature sensor circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
Shift solenoid valve SLT circuit
Not circuit malfunction
ECT (Engine Coolant Temperature) sensor circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric Throttle Control System)
Not system down
Transmission range
"D"
ECT
40°C (104°F) or more
Spark advance from Max. retard timing by KCS control
0°crankshaft angle or more
Engine
Starting
Transfer range
"High" *1
TFT temperature
10°C (50°F) or more

*1: Following conditions met
Transfer range "HIGH" *1 (This condition is applied only 4WD) 
Vehicle speed sensor circuit
Not circuit malfunction
Output shaft speed sensor circuit
Not circuit malfunction
Transfer output speed
143 rpm or more
NO/NOtf (Transfer input speed/Transfer output speed)
0.9 to 1.1

TYPICAL MALFUNCTION THRESHOLDS


ON malfunction 
Summation of C1 clutch heat generations
Specified value

INSPECTION PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the OBD II scan tool or the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the OBD II scan tool or the intelligent tester main switch ON.

  1. When you use intelligent tester:
    Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".

  1. Read the DTCs using the OBD II scan tool or the intelligent tester.

    Result:

    Display (DTC output)
    Proceed to
    Only "P2714" is output
    A
    "P2714" and other DTCs
    B

    HINT:
    If any other codes besides "P2714" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F)
  2. Be careful to prevent SST hose from interfering with the exhaust pipe.
  3. This check must be conducted after checking and adjusting engine.
  4. Perform under condition that A/C is OFF.

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Turn the ignition switch off.

  1. Lift the vehicle up.



    G020657E02
  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Lower the vehicle.

  1. Fully apply the parking brake and chock the 4 wheels.

  1. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  1. Start the engine.

  1. Warm up the ATF (Automatic Transmission Fluid).

  1. Measure the line pressure when the engine is idling.

  1. Turn on the tester.

  1. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SOLENOID (SLT)".

  1. Follow the instructions on the tester and perform the ACTIVE TEST.

  1. Measure the line pressure with SST.

    Item
    Test Details
    LINE PRESS UP*
    [Test Details]
    Operate the shift solenoid SLT and raise the line pressure.
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. IDL: ON

    HINT:
    OFF: Line pressure up (When the active test of "SOLENOID (SLT)" is performed, the ECM commands the SLT solenoid to turn off).
    ON: No action (normal operation)

    *: "LINE PRESS UP" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

    OK:
    The line pressure changes as specified when performing the ACTIVE TEST.



NG
Go to step 9
OK


3.PERFORM RUNNING TEST

NOTICE:
This test should always be performed with at least 2 people.

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
The DATA LIST can be displayed during the ACTIVE TEST.

  1. Warm up the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn on the tester.

  1. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST".

  1. Follow the instructions on the tester and read the ACTIVE TEST.

    HINT:
    While driving, the shift position can be forcibly changed with the intelligent tester.


    Item
    Test Details
    Diagnostic Note
    SHIFT
    [Test Details]
    Operate the shift solenoid valve and set the each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check the operation of the shift solenoid valves.

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shiftings must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shiftings must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the intelligent tester.

  1. Compare the ECM gear shift command and the actual gear position.

    Result:

    ECM gear shift command
    1st
    2nd
    3rd
    4th
    5th
    Proceed to
    Actual gear position under malfunction
    Shift solenoid S1
    Stuck ON
    1st
    2nd
    2nd
    1st
    N*1
    A
    Stuck OFF
    4th
    3rd
    3rd
    4th
    5th
    Shift solenoid S2
    Stuck ON*2
    2nd
    2nd
    3rd
    3rd
    N*1
    B
    Stuck OFF*3
    1st
    1st
    4th
    4th
    5th
    Shift solenoid SL2
    Stuck ON
    1st
    2nd
    3rd
    4th
    N*1
    C
    Stuck OFF
    1st
    2nd
    3rd
    4th
    5th
    Shift solenoid SR
    Stuck ON*4
    1st
    2nd
    3rd
    4th
    5th
    D
    Stuck OFF*5
    1st
    2nd
    3rd
    4th
    4th

    HINT:
    1. *1: Neutral
    2. *2: When shift solenoid S2 is stuck ON, the vehicle cannot drive in reverse.
    3. *3: When shift solenoid S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also the 5th to 4th down-shift will have time lag.
    4. *4: Stuck ON condition can be determined by checking if shift shock has increased excessively.
    5. *5: When shift solenoid SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
    6. Gear shift can be determined by paying attention to changes in rpm.



OK
Go to step 9

B
Go to step 5

C
Go to step 6

D
Go to step 7
A


4.INSPECT SHIFT SOLENOID VALVE S1


    A110986E04
  1. Remove the shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (S1) - Solenoid Body (S1)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE S1 

5.INSPECT SHIFT SOLENOID VALVE S2


    A110987E04
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE S2 

6.INSPECT SHIFT SOLENOID VALVE SL2


    D025466E22
  1. Remove the shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE SL2 

7.INSPECT SHIFT SOLENOID VALVE SR


    A110988E05
  1. Remove the shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (SR) - Solenoid Body (SR)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SR
OK


8.INSPECT SHIFT SOLENOID VALVE SL1


    D025466E21
  1. Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE SL1 

9.INSPECT SHIFT SOLENOID VALVE SLT


    G020767E08
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


10.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on each valve.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


11.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

OK:
The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY