Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2UZ-FE)

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0705
  1. (2-trip detection logic)
    1. All switches are OFF simultaneously for P(NSW), R, N(NSW), D, 3 and 2 positions.
    2. 2 or more switches are ON simultaneously for P(NSW), R, N(NSW), (D 4), 3 and (2 L) positions.
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 4, 3, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0705: Park/neutral position switch/Verify switch input
Required sensors/Components
Park/neutral position switch
Frequency of operation
Continuous
Duration
Condition (A) and (C)
2 sec.
Condition (B)
60 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
None
Engine switch
ON
Battery voltage
10.5 V or more

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: Condition (A), (B) or (C)

  1. Condition (A) 
    Number of the following signal input at the same time
    2 or more
    NSW switch
    ON
    R switch
    ON
    D switch
    ON
    3 switch
    ON
    2 switch
    ON

    All of following conditions are met
    Condition (B) 
    NSW switch
    OFF
    R switch
    OFF
    D switch
    OFF
    3 switch
    OFF
    2 switch
    OFF

    Both (i) and (ii) are met(i) One of following conditions is met
    Condition (C) 
    NSW switch
    ON
    R switch
    ON
    (ii) One of following condition is met

    4 switch
    ON
    L switch
    ON

COMPONENT OPERATING RANGE


Park/neutral position switch
The park/neutral position switch sends only one signal to the ECM.

WIRING DIAGRAM


G039611E01


INSPECTION PROCEDURE


DATA LIST

HINT:
According to the DATA LIST displayed by the intelligent tester, you can read the value of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of troubleshooting is one method to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / DATA LIST".

  7. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item/Range (display)
    Normal Condition
    Diagnostic Note
    PNP SW [NSW]
    PNP Switch Status/ON or OFF
    Shift lever position is;
    P and N: ON
    Except P and N: OFF
    When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    LOW
    PNP Switch Status/ON or OFF
    Shift lever position is;
    L: ON
    Except L: OFF
    ↑
    2ND
    PNP Switch Status/ON or OFF
    Shift lever position is;
    2 and L: ON
    Except 2 and L: OFF
    ↑
    3RD
    PNP Switch Status/ON or OFF
    Shift lever position is;
    3: ON
    Except 3: OFF
    ↑
    4th/DRIVE
    PNP Switch Status/ON or OFF
    Shift lever position is;
    4: ON
    Except 4: OFF
    ↑
    REVERSE
    PNP Switch Status/ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    ↑
    DRIVE
    PNP Switch Status/ON or OFF
    Shift lever position is;
    D and 4: ON
    Except D and 4: OFF
    ↑

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C110340E39
  1. Jack up the vehicle.

  1. Disconnect the park/neutral position switch connector.

  1. Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    2 - 6 and 4 - 5
    Below 1 Ω
    Except P
    ↑
    10 kΩ or higher
    R
    1 - 2
    Below 1 Ω
    Except R
    ↑
    10 kΩ or higher
    N
    2 - 9 and 4 - 5
    Below 1 Ω
    Except N
    ↑
    10 kΩ or higher
    D and 4
    2 - 7
    Below 1 Ω
    Except D and 4
    ↑
    10 kΩ or higher
    3
    2 - 3
    Below 1 Ω
    Except 3
    ↑
    10 kΩ or higher
    2 and L
    2 - 8
    Below 1 Ω
    Except 2 and L
    ↑
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


2.INSPECT SHIFT LOCK CONTROL ECU SUB-ASSEMBLY (TRANSMISSION CONTROL SWITCH)


    D029380E10
  1. Connect the park/neutral position switch connector.

  1. Disconnect the shift lock control ECU connector.

  1. Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    D
    9 - 2 (NSSD - ATD)
    Below 1 Ω
    4
    10 kΩ or higher
    D
    9 - 3 (NSSD - AT4)
    10 kΩ or higher
    4
    Below 1 Ω
    2
    10 - 5 (NSSL - AT2)
    Below 1 Ω
    L
    10 kΩ or higher
    2
    10 - 4 (NSSL - ATL)
    10 kΩ or higher
    L
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU SUB-ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    A131509E63
  1. Connect the shift lock control ECU connector.

  1. Turn the ignition switch to the ON position, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:

    Shift Position
    Tester Connection
    Specified Condition
    P and N
    E5-8 (NSW) - Body ground
    Below 2 V
    Except P and N
    ↑
    10 to 14 V
    R
    E7-11 (R) - Body ground
    10 to 14 V*
    Except R
    ↑
    Below 1 V
    D and 4
    E7-21 (D) - Body ground
    10 to 14 V
    Except D and 4
    ↑
    Below 1 V
    3
    E7-19 (3) - Body ground
    10 to 14 V
    Except 3
    ↑
    Below 1 V
    2 and L
    E7-10 (2) - Body ground
    10 to 14 V
    Except 2 and L
    ↑
    Below 1 V
    L
    E7-9 (L) - Body ground
    10 to 14 V
    Except L
    ↑
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the turning on of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM