Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)

DTC    P2757    Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses the signals from the throttle position sensor, Air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
C108926E01
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect a mechanical problems of the shift solenoid valve SLU, valve body and torque converter clutch.

DTC No.
DTC Detection Condition
Trouble Area
P2757
Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock-up remains ON in the lock-up OFF range.
(2-trip detection logic)
  1. Shift solenoid valve SLU remains open or closed
  2. Valve body is blocked
  3. Torque converter clutch
  4. Automatic transmission (clutch, brake or gear, etc.)
  5. Line pressure is too low

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the turbine (input) speed sensor NT, output speed sensor SP2, engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input turbine rpm (NT). The ECM calculates the actual transmission gear by comparing input turbine rpm (NT) to output shaft rpm (SP2). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to the shift solenoid SLU. When the SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter clutch.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in the shift solenoid valve SLU or lock-up system performance.
The ECM will turn on the MIL and store the DTC.
Example:
When any of the following is met, the system judges it as a malfunction.
  1. There is a difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.
    (Engine speed is at least 70 rpm greater than input turbine speed.)
  2. There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up off.
    (The difference between engine speed and input turbine speed is less than 35 rpm.)

MONITOR STRATEGY


Related DTCs
P2757:
Shift solenoid valve SLU/OFF malfunction
Shift solenoid valve SLU/ON malfunction
Required sensors/Components
Shift solenoid valve SLU, Valve body, Vehicle speed sensor, Speed sensor (NT), Speed sensor (NO), Throttle position sensor
Frequency of operation
Continuous
Duration
OFF malfunction (A)
2sec.
OFF malfunction (B)
0.4 sec.
ON malfunction
1.8 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The following items are common to all conditions below. 
The monitor will run whenever this DTC is not present.
None
Turbine speed sensor circuit
Not circuit malfunction
Output speed sensor circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Torque converter clutch pressure control solenoid circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric throttle control system)
Not system down
Transmission range
"D"
ECT
40°C (104°F) or more
Spark advance from Max. retard timing by KCS control
0° CA or more
Engine
Starting
ECM selected gear
4th or 5th
Vehicle speed
25 km/h (15.5 mph) or more
Shift solenoid valve S1 circuit
Not on malfunction
Shift solenoid valve S2 circuit
Not on malfunction
Shift solenoid valve SL2 circuit
Not on malfunction
1-2 shift valve circuit
Not on malfunction
Transfer neutral position switch
OFF
Transfer range
"High" *1

*1: Following conditions met
Transfer range "HIGH" *1 (This condition is applied only 4WD) 
Vehicle speed sensor circuit
Not circuit malfunction
Output shaft speed sensor circuit
Not circuit malfunction
Transfer output speed
143 rpm or more
NO/NOtf (Transfer input speed/Transfer output speed)
0.9 to 1.1

OFF malfunction (A) 
ECM lock-up command
ON (SLU pressure: 513 kPa or more)
Vehicle speed
Less than 100 km/h (62.2 mph)

OFF malfunction (B) 
ECM selected gear
2nd
Vehicle speed
2 km/h (1.2 mph) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
6.5% or more at 2,000 rpm (Varies with engine speed)

ON malfunction 
ECM lock-up command
OFF (SLU pressure: less than 4 kPa)
Throttle valve opening angle
7% or more
Vehicle speed
Less than 60 km/h (37.3 mph)

TYPICAL MALFUNCTION THRESHOLDS

Both of the following condition are met: OFF malfunction (A) and (B)

OFF malfunction (A): 
Engine speed - Turbine speed (NE - NT)
70 rpm or more

OFF malfunction (B): 
Turbine speed/Output speed (NT/NO)
Less than 3.30, or more than 7.50

2 detections are necessary per driving cycle:1st detection; temporary flag ON2md detection; pending fault code ONVehicle speed must be under 6.2mph (10 km/h) once before 2nd detection.
ON malfunction (A): 
Engine speed - Turbine speed (NE - NT)
Less than 35 rpm

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST".

  7. According to the display on the tester, perform the "ACTIVE TEST".

    Item
    Test Details
    Diagnostic Note
    LOCK UP
    [Test Details]
    Control the shift solenoid SLU to set the automatic transmission to the lock-up condition.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle Speed: 60 km/h (37 mph) or more
    Possible to check the SLU operation.

    HINT:
    1. This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.
    2. This test can be conducted with the 5th gear.



  8. Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.


    G029214E02

    HINT:
    1. When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
    2. Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757)
  1. Connect the OBD II scan tool or the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) position and push the OBD II scan tool or the intelligent tester main switch ON.

  1. When you use intelligent tester:
    Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".

  1. Read the DTCs using the OBD II scan tool or the intelligent tester.

    Result:

    Display (DTC output)
    Proceed to
    Only "P2757" is output
    A
    "P2757" and other DTCs
    B

    HINT:
    If any other codes besides "P2757" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT SHIFT SOLENOID VALVE SLU


    G020767E09
  1. Remove the shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLU
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on each valve.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

OK:
The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY