DTC P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2757 | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock-up remains ON in the lock-up OFF range. (2-trip detection logic) |
|
| Related DTCs | P2757: Shift solenoid valve SLU/OFF malfunction Shift solenoid valve SLU/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLU, Valve body, Vehicle speed sensor, Speed sensor (NT), Speed sensor (NO), Throttle position sensor |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) 2sec. OFF malfunction (B) 0.4 sec. ON malfunction 1.8 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | None |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Torque converter clutch pressure control solenoid circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric throttle control system) | Not system down |
| Transmission range | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| ECM selected gear | 4th or 5th |
| Vehicle speed | 25 km/h (15.5 mph) or more |
| Shift solenoid valve S1 circuit | Not on malfunction |
| Shift solenoid valve S2 circuit | Not on malfunction |
| Shift solenoid valve SL2 circuit | Not on malfunction |
| 1-2 shift valve circuit | Not on malfunction |
| Transfer neutral position switch | OFF |
| Transfer range | "High" *1 |
| Vehicle speed sensor circuit | Not circuit malfunction |
| Output shaft speed sensor circuit | Not circuit malfunction |
| Transfer output speed | 143 rpm or more |
| NO/NOtf (Transfer input speed/Transfer output speed) | 0.9 to 1.1 |
| ECM lock-up command | ON (SLU pressure: 513 kPa or more) |
| Vehicle speed | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down shift point or more |
| Throttle valve opening angle | 7.0% or more at 2,000 rpm (Varies with engine speed) |
| ECM lock-up command | OFF (SLU pressure: less than 4 kPa) |
| Throttle valve opening angle | 9% or more |
| Vehicle speed | Less than 60 km/h (37.3 mph) |
| Engine speed - Turbine speed (NE - NT) | 70 rpm or more |
| Turbine speed/Output speed (NT/NO) | Less than 3.30, or more than 7.50 |
| Engine speed - Turbine speed (NE - NT) | Less than 35 rpm |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST".
According to the display on the tester, perform the "ACTIVE TEST".
| Item | Test Details | Diagnostic Note |
| LOCK UP | [Test Details] Control the shift solenoid SLU to set the automatic transmission to the lock-up condition. [Vehicle Condition]
| Possible to check the SLU operation. |
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757) |
Connect the OBD II scan tool or the intelligent tester to the DLC3.
Turn the engine switch on (IG) position and push the OBD II scan tool or the intelligent tester main switch ON.
When you use intelligent tester:
Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".
Read the DTCs using the OBD II scan tool or the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P2757" is output | A |
| "P2757" and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLU |
![]() |
Remove the shift solenoid valve SLU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
|
| ||||
| OK | ||
| ||