DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2238 P2241 |
|
|
| P2239 P2242 | AF+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| P2252 P2255 | AF- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic) |
|
| P2253 P2256 | AF- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| Related DTCs | P2238: A/F sensor (Bank 1) open circuit between AF+ and AF- P2238: A/F sensor (Bank 1) short circuit between AF+ and AF- P2238: A/F sensor (Bank 1) short circuit between AF+ and GND P2239: A/F sensor (Bank 1) short circuit between AF+ and +B P2241: A/F sensor (Bank 2) open circuit between AF+ and AF- P2241: A/F sensor (Bank 2) short circuit between AF+ and AF- P2241: A/F sensor (Bank 2) short circuit between AF+ and GND P2242: A/F sensor (Bank 2) short circuit between AF+ and +B P2252: A/F sensor (Bank 1) short circuit between AF- and GND P2253: A/F sensor (Bank 1) short circuit between AF- and +B P2255: A/F sensor (Bank 2) short circuit between AF- and GND P2256: A/F sensor (Bank 2) short circuit between AF- and +B |
| Required Sensors/Components | A/F sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds: A/F sensor open circuit between AF+ and AF- 5 seconds: Others |
| MIL Operation | 2 driving cycles: A/F sensor open circuit between AF+ and AF- Immediate: Others |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Duration while all of following conditions met | - |
| AF+ terminal voltage | 0.5 to 4.5 V |
| AF- terminal voltage | 0.5 to 4.5 V |
| Difference between AF+ and AF- terminal voltages | 0.1 to 0.8 V |
| ECT | More than 0°C (32°F): closed-loop fuel control enable temperature |
| Engine | Running |
| Time after fuel - cut OFF | 5 seconds or more |
| Fuel-cut | OFF |
| A/F sensor heater | ON |
| Time after ignition switch OFF to ON | 5 seconds or more |
| Battery voltage | 11 V or more |
| Ignition switch | ON |
| Battery voltage | 11 V or more |
| Ignition switch | ON |
| Time after ignition switch is OFF to ON | 5 seconds or more |
| A/F sensor admittance | Below 0.022 1/Ω |
| AF+ terminal voltage | 0.5 V or less |
| Difference between AF+ and AF- terminal voltages | 0.1 V or less |
| AF+ terminal voltage | More than 4.5 V |
| AF- terminal voltage | 0.5 V or less |
| AF- terminal voltage | More than 4.5 V |
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Areas | ||
| 1 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A12 or A13 Air Fuel Ratio (A/F) sensor connector.
Measure the resistance of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.INSPECT A/F RELAY |
![]() |
Remove the A/F relay from the engine room relay block.
Measure the resistance of the A/F relay.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the A/F relay.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A12 or A13 A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (2) - Body ground | Between 9 V and 14 V |
Turn the ignition switch to OFF.
Disconnect the E5 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT (A12-1) - HA1A (E5-2) HT (A13-1) - HA2A (E5-1) | Below 1 Ω |
| AF+ (A12-3) - A1A+ (E5-22) AF+ (A13-3) - A2A+ (E5-23) | Below 1 Ω |
| AF- (A12-4) - A1A- ((E5-30) AF- (A13-4) - A2A- (E5-31) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HT (A12-1) or HA1A (E5-2) - Body ground HT (A13-1) or HA2A (E5-1) - Body ground | 10 kΩ or higher |
| AF+ (A12-3) or A1A+ (E5-22) - Body ground AF+ (A13-3) or A2A+ (E5-23) - Body ground | 10 kΩ or higher |
| AF- (A12-4) or A1A- ((E5-30) - Body ground AF- (A13-4) or A2A- (E5-31) - Body ground | 10 kΩ or higher |

|
| ||||
| OK | ||
| ||