DTC P0781 1-2 Shift (1-2 Shift Valve) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0781 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0781: Valve body/Rationality check |
| Required sensors/Components (Main) | Valve body |
| Required sensors/Components (Related) | Automatic transmission assembly, Speed sensor (NT), Speed sensor (NO), Vehicle speed sensor, Throttle position sensor |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (B): 0.4 sec. Condition (C): 3 sec. Condition (D): 0.5 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | None |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric throttle control system) | Not system down |
| Transmission range | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| Transfer range | "High" *1 |
| Vehicle speed sensor circuit | Not circuit malfunction |
| Output shaft speed sensor circuit | Not circuit malfunction |
| Transfer output speed | 143 rpm or more |
| NO/NOtf (Transfer input speed/Transfer output speed) | 0.9 to 1.1 |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down shift point or more |
| Throttle valve opening angle | 7.0% or more at 2,000 rpm (Vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 7.0% or more at 2,000 rpm (Vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) (After transition from 4th to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| Turbine speed/Output speed | 3.30 to 7.50 |
| Turbine speed/Output speed | 1.28 to 1.53 |
| Turbine speed - Output speed x 4th gear ratio (NT - NO x 4th gear ratio) | 1,000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1,000 rpm or more |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781) |
Connect the OBD II scan tool or the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the OBD II scan tool or the intelligent tester main switch ON.
When you use intelligent tester:
Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".
Read the DTCs using the OBD II scan tool or the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P0781" is output | A |
| "P0781" and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SHIFT".
According to the display on the tester, perform the "ACTIVE TEST".
| Item | Test Details | Diagnostic Note |
| SHIFT | [Test Details] Operate the shift solenoid valve and set the each shift position by yourself. [Vehicle Condition]
| Possible to check the operation of the shift solenoid valves. |
|
| ||||
| OK | |
| 3.CLEAR THE DTC AND RUNNING TEST |
Clear the DTC, and check DTC again after conducting the "MONITOR DRIVE PATTERN FOR ECT TEST" (Click here).
|
| ||||
| OK | ||
| ||