Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2UZ-FE)

DTC    P0781    1-2 Shift (1-2 Shift Valve)

for Preparation Click here


SYSTEM DESCRIPTION


  1. The 1-2 shift valve performs shifting to 1st gear and other gears.
    G037197E02

    DTC No.
    DTC Detection Condition
    Trouble Area
    P0781
    The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)
    1. Shift solenoid valve SLT remains open or closed
    2. Valve body is blocked up or stuck (1-2 shift valve)
    3. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the direction the spring compresses.
The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF" and switching oil pressure to the valves in the valve body.
The ECM calculates the "actual" transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift solenoids, valve body, and the transmission clutches, brakes, and gears. If the ECM detects that the actual gear position and the commanded gear position are different, it will illuminate the MIL and store the DTC .

MONITOR STRATEGY


Related DTCs
P0781: Valve body/Rationality check
Required sensors/Components (Main)
Valve body
Required sensors/Components (Related)
Automatic transmission assembly, Speed sensor (NT), Speed sensor (NO), Vehicle speed sensor, Throttle position sensor
Frequency of operation
Continuous
Duration
Condition (A) and (B): 0.4 sec.
Condition (C): 3 sec.
Condition (D): 0.5 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever this DTC is not present.
None
Turbine speed sensor circuit
Not circuit malfunction
Output speed sensor circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine coolant temperature) sensor circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric throttle control system)
Not system down
Transmission range
"D"
ECT
40°C (104°F) or more
Spark advance from Max. retard timing by KCS control
0° CA or more
Engine
Starting

Condition (A) 
ECM selected gear
2nd
Vehicle speed
2 km/h (1.2 mph) or more
Output speed
2nd → 1st down shift point or more
Throttle valve opening angle
7.0% or more at 2,000 rpm (Vary with engine speed)

Condition (B) 
ECM selected gear
4th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
7.0% or more at 2,000 rpm (Vary with engine speed)

Condition (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed (During transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

Condition (D) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed (After transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: Condition (A), and Condition (B), (C) or (D)

  1. Condition (A) 
    Turbine speed/Output speed
    3.30 to 7.50

    Condition (B) 
    Turbine speed/Output speed
    1.28 to 1.53

    Condition (C) 
    Turbine speed - Output speed x 4th gear ratio
    (NT - NO x 4th gear ratio)
    1,000 rpm or more

    Condition (D) 
    Turbine speed - Output speed x 5th gear ratio
    (NT - NO x 5th gear ratio)
    1,000 rpm or more

INSPECTION PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0781)
  1. Connect the OBD II scan tool or the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the OBD II scan tool or the intelligent tester main switch ON.

  1. When you use intelligent tester:
    Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".

  1. Read the DTCs using the OBD II scan tool or the intelligent tester.

    Result:

    Display (DTC output)
    Proceed to
    Only "P0781" is output
    A
    "P0781" and other DTCs
    B

    HINT:
    If any other codes besides "P0781" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER

HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Warm up the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn on the tester.

  1. Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SHIFT".

  1. According to the display on the tester, perform the "ACTIVE TEST".

    HINT:
    While driving, the shift position can be forcibly changed with the intelligent tester.
    Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you to confirm the problem (Click here).


    Item
    Test Details
    Diagnostic Note
    SHIFT
    [Test Details]
    Operate the shift solenoid valve and set the each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check the operation of the shift solenoid valves.

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shiftings must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shiftings must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the intelligent tester.

    OK:
    Gear position changes in accordance with the tester command.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


3.CLEAR THE DTC AND RUNNING TEST
  1. Clear the DTC, and check DTC again after conducting the "MONITOR DRIVE PATTERN FOR ECT TEST" (Click here).

    OK:
    No DTC code



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

END