Home › ENGINE ยท 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Condition
Trouble Area
P0116
(1) With the engine coolant temperature was 35°C (95°F) or more but less than 60°C (140°F) when the engine was started, and if conditions (a) and (b) are met:
(a) Vehicle has accelerated and decelerated.
(b) Engine coolant temperature remains within 3°C (5.4°F) of the initial engine coolant temperature (2 trip detection logic).
(2) If the engine coolant temperature is more than 60°C (140°F) when the engine is started and the vehicle has accelerated and decelerated
(3) If the engine coolant temperature sensor records a temperature variation below 1°C (1.8°F) successively 6 times (6 trip detection logic)
Engine coolant temperature sensor

MONITOR DESCRIPTION

The Engine Coolant Temperature (ECT) sensor is used to monitor the engine coolant temperature. The ECT sensor has a thermistor that varies its resistance depending on the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. The variations in resistance are reflected in the voltage output from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the ECT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the ECT sensor and sets a DTC.
Examples:
  1. Upon starting the engine, the ECT is between 35°C (95°F) and 60°C (140°F). If after driving for 250 seconds, the ECT still remains within 3°C (5.4°F) of the starting temperature, a DTC will be set (2 trip detection logic).
  2. Upon starting the engine, the ECT is over 60°C (140°F). If, after driving for 250 seconds, the ECT still remains within 1°C (1.8°F) of the starting temperature, a DTC will be set (6 trip detection logic).

MONITOR STRATEGY


Related DTCs
P0116: Engine Coolant Temperature (ECT) sensor stuck (low ECT)
P0116: ECT sensor stuck (high ECT)
Required Sensors/Components (Main)
Engine Coolant Temperature sensor
Required Sensors/Components (Related)
Intake air temperature sensor, Crankshaft position sensor, Mass air flow meter
Frequency of Operation
Continuous
Duration
250 seconds or more
MIL Operation
2 driving cycles: ECT sensor stuck
6 driving cycles: ECT sensor stuck at high ECT
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
P0100 - P0103 (MAF sensor)

Engine Coolant Temperature sensor stuck (low Engine Coolant Temperature): 
Cumulative idle off period
250 seconds or more
Vehicle speed increase of 18.6 mph (30km/h) or more
10 times or more
Engine coolant temperature
35 to 60°C (95 to 140°F)
Intake air temperature
-6.7°C (20°F) or more
Intake air temperature sensor circuit fail
Not detected

Engine Coolant Temperature sensor stuck (high Engine Coolant Temperature): 
ECT at engine start
60°C (140°F) or more
ECT sensor circuit fail
Not detected
IAT since engine start
-6.7°C (20°F) or more
IAT sensor circuit fail
Not detected
Stop and go*1
Once or more
Steady driving and stop*2
Once or more
Engine running time after engine start
0.3 sec. or more

HINT:
*1: Vehicle is stopped for 20 seconds or more and accelerated to more than 44 mph (70 km/h) within 40 seconds.
*2: Follow these steps: 1) vehicle is driven at 40 mph (65 km/h) or more for 30 seconds or more and the vehicle speed reaches 44 mph (70 km/h); 2) vehicle is decelerated from 40 mph (65 km/h) to 2 mph (3 km/h) or less within 35 seconds; and 3) vehicle is stopped for 10 seconds.


TYPICAL MALFUNCTION THRESHOLDS


Engine Coolant Temperature sensor stuck (low Engine Coolant Temperature): 
Engine coolant temperature change
Less than 3°C (5.4°F)

Engine Coolant Temperature sensor stuck (high Engine Coolant Temperature): 
Engine coolant temperature change
1°C (1.8°F) or less

COMPONENT OPERATING RANGE


Engine coolant temperature
Varies with actual engine coolant temperature

WIRING DIAGRAM

Refer to DTC P0115 .

INSPECTION PROCEDURE

HINT:
  1. If DTC P0115, P0116, P0117, P0118 and P0125 are output simultaneously, the ECT sensor circuit may be open or shorted. Perform the troubleshooting of DTC P0115, P0117 or P0118 first.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0116
    A
    P0116 and other DTCs
    B



B
GO TO RELEVANT DTC CHART
A


2.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat .

    Standard:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR