Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0100    Mass Air Flow Circuit Malfunction

DTC    P0102    Mass Air Flow Circuit Low

DTC    P0103    Mass Air Flow Circuit High

for Preparation Click here


DESCRIPTION

The Mass Air Flow (MAF) meter measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provide a proper air fuel ratio. Inside the MAF meter, there is a heated platinum wire exposed to the flow of intake air.
By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the air passing through the sensor. The ECM interprets this voltage as the intake air amount.
The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the set temperature.

G032710E01


DTC No.
DTC Detection Condition
Trouble Area
P0100
Open or short in mass air flow meter circuit with more than 3 seconds engine speed 4,000 rpm or less
  1. Open or short in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM
P0102
Open or short in mass air flow meter circuit with more than 3 seconds engine speed 4,000 rpm or less
  1. Open in mass air flow meter circuit
  2. Short in ground circuit
  3. Mass air flow meter
  4. ECM
P0103
Open in mass air flow meter circuit with more than 3 seconds (E2G circuit) engine speed 4,000 rpm or less
Short in mass air flow meter circuit with more than 3 seconds (+B circuit) engine speed 4,000 rpm or less
  1. Open in mass air flow meter circuit (E2G circuit)
  2. Short in mass air flow meter circuit (+B circuit)
  3. Mass air flow meter
  4. ECM

HINT:
After confirming DTC P0100, P0102 or P0103, use the intelligent tester to confirm the MAF ratio from the ALL menu (to reach the ALL menu: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL).


Mass Air Flow Rate (g/sec)
Malfunction
Approximately 0.0
  1. MAF meter power source circuit open
  2. VG circuit open or short
271.0 or more
E2G circuit open

MONITOR DESCRIPTION

If there is a defect in the Mass Air Flow (MAF) meter or an open or short circuit, the voltage level will deviate outside the normal operating range. The ECM interprets this deviation as a defect in the MAF meter and sets a DTC.
Example:
When the sensor output voltage is less than 0.2 V or more than 4.9 V and if either condition continues for more than 3 seconds, the ECM will set a DTC.

MONITOR STRATEGY


Related DTCs
P0100: MAF meter range check (fluttering)
P0102: MAF meter range check (low voltage)
P0103: MAF meter range check (high voltage)
Required Sensors/Components (Main)
MAF meter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
Immediate: Engine RPM is less than 4,000 rpm
2 driving cycles: Engine RPM is 4,000 rpm or more
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
The typical enabling condition is not available
-

TYPICAL MALFUNCTION THRESHOLDS


P0100: 
MAF meter voltage
Less than 0.2 V or more than 4.9 V

P0102: 
MAF meter voltage
Less than 0.2 V

P0103: 
MAF meter voltage
More than 4.9 V

COMPONENT OPERATING RANGE


MAF meter voltage
Between 0.4 and 2.2 V

WIRING DIAGRAM


A131129E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE OF INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect the intelligent tester to the CAN VIM. Then connect the CAN VIM to the DLC3.

  1. Allow the engine to idle.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / MAF.

  1. Read the values displayed on the tester.

    Result:

    Mass Air Flow Rate (g/sec)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*1)
    C

HINT:
*1: The value must change when the throttle valve is open or closed.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.INSPECT MASS AIR FOW METER (POWER SOURCE VOLTAGE)


    A054396E48
  1. Disconnect the M1 Mass Air Flow (MAF) meter connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (M1-1) - Body ground
    9 to 14 V

  1. Reconnect the MAF meter connector.



NG
Go to step 5
OK


3.INSPECT ECM (VG VOLTAGE)


    E118245E22
  1. Start the engine.

  1. Measure the voltage of the E4 ECM connector.

    HINT:
    Move the shift lever to P or N and turn the A/C switch OFF.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    VG (E4-30) - E2G (E4-29)
    Engine is idling
    0.5 to 3.0 V



OK
REPLACE ECM
NG


4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A115696E02
  1. Disconnect the M1 mass air flow meter connector.

  1. Disconnect the E4 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    VG (M1-3) - VG (E4-30)
    Below 1 Ω
    E2G (M1-2) - E2G (E4-29)
    Below 1 Ω
    VG (M1-3) or VG (E4-30) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the MAF connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER 

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - EFI RELAY)


    A137830E01
  1. Remove the EFI No. 2 fuse from the engine room R/B.

  1. Measure the resistance in the EFI No. 2 fuse.

    Standard:
    Below 1 Ω

  1. Reinstall the EFI No. 2 fuse.

  1. Disconnect the M1 mass air flow meter connector.

  1. Remove the EFI relay from the engine room R/B.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    +B (M1-1) - Engine room R/B (EFI relay terminal 3)
    Below 1 Ω
    +B (M1-1) or Engine room R/B (EFI relay terminal 3) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT 

6.INSPECT ECM (SENSOR GROUND)


    E118245E23
  1. Measure the resistance of the ECM connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E2G (E4-29) - Body ground
    Below 1 Ω



NG
REPLACE ECM
OK


7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A137865E01
  1. Disconnect the M1 mass air flow meter connector.

  1. Disconnect the E4 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    VG (M1-3) - VG (E4-30)
    Below 1 Ω
    E2G (M1-2) - E2G (E4-29)
    Below 1 Ω
    VG (M1-3) or VG (E4-30) - Body ground
    10 kΩ or higher
    E2G (M1-2) or E2G (E4-29) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER