Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0341    Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0346    Camshaft Position Sensor "A" Circuit Range / Performance (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT sensor consists of a magnet, an iron core and a pick-up coil. This sensor monitors a timing rotor located on the camshaft and is used by the ECM to detect the camshaft angle. The camshaft rotation synchronizes with the crankshaft rotation, and this sensor communicates the rotation of the camshaft timing rotor as a pulse signal to the ECM.
If there is no signal from the VVT sensor even though the engine is turning or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction in the sensor and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0340
P0345
  1. No VVT sensor signal to ECM during cranking (2 trip detection logic)
  2. No VVT sensor signal to ECM with engine speed 600 rpm or more (1 trip detection logic)
  1. Open or short in VVT sensor circuit
  2. VVT sensor
  3. Intake camshaft
  4. Timing belt has a jumped tooth
  5. ECM
P0341
P0346
While crankshaft rotates twice, VVT sensor signal is input to ECM 12 times or more (1 trip detection logic)
Same as DTC No. P0340/P0345

HINT:
  1. DTC P0340 and P0345 indicate a malfunction related to the VVT sensor (+) circuit
    (wire harness (from ECM to VVT sensor) and VVT sensor).
  2. DTC P0341 and P0346 indicate a malfunction related to the VVT sensor (-) circuit
    (wire harness (from ECM to VVT sensor) and VVT sensor).


  1. A106052E02
  2. Reference: Inspect using an oscilloscope.
    During cranking or idling, check the waveform of the ECM connector.
Tester Connection
Specified Condition
VV1+ (E6-25) - VV1- (E6-24)
Correct waveform is as shown
VV2+ (E6-18) - VV2- (E6-28)
Correct waveform is as shown
NE+ (E6-21) - NE- (E6-20)
Correct waveform is as shown
G2+ (E6-19) - G2- (E6-29)
Correct waveform is as shown

MONITOR DESCRIPTION

If there is no signal from the VVT sensor even though the engine is revolving, or if the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (bank 1) range check / rationality
P0341: VVT sensor (bank 1) range check / rationality
P0345: VVT sensor (bank 2) range check / rationality
P0346: VVT sensor (bank 2) range check / rationality
Required Sensors/Components (Main)
VVT sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
P0340, P0345 case 1: 2 driving cycles
P0340, P0345 case 2, P0341, P0346: Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor will run whenever these DTCs are not present
None

P0340, P0345 Case 1: 
Starter
ON
Minimal battery voltage while starter ON
Less than 11 V

P0340, P0345 Case 2: 
Engine RPM
600 rpm or more
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

P0341, P0346: 
Starter
After OFF to ON timing
Engine revolution
720°CA

TYPICAL MALFUNCTION THRESHOLDS


P0340, P0345 Case 1: 
VVT sensor signal
No signal

P0340, P0345 Case 2: 
VVT sensor signal
No signal

P0341, P0346: 
VVT sensor count
12 or more / 720°CA (=Engine 2 revolutions)

COMPONENT OPERATING RANGE


VVT sensor signal input during every 720°CA
3

WIRING DIAGRAM


A133711E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT VVT SENSOR (RESISTANCE)


    A066132E08
  1. Disconnect the V3 and V4 VVT sensor connectors.

  1. Measure the resistance of the VVT sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    835 to 1,400 Ω
    1 - 2
    Hot
    1,060 to 1,645 Ω

    HINT:
    In the above chart, the terms "cold" and "hot" refer to the temperature of the coils.
    "Cold" means approximately -10 to 50°C (14 to 122°F).
    "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE VVT SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)


    A115706E02
  1. Disconnect the V3 or V4 VVT sensor connectors.

  1. Disconnect the E6 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    VVT sensor (V3-1) - VV1+ (E6-25)
    Below 1 Ω
    VVT sensor (V3-2) - VV1- (E6-24)
    VVT sensor (V4-1) - VV2+ (E6-18)
    VVT sensor (V4-2) - VV2- (E6-28)
    VVT sensor (V3-1) or VV1+ (E6-25) - Body ground
    10 kΩ or higher
    VVT sensor (V3-2) or VV1- (E6-24) - Body ground
    VVT sensor (V4-1) or VV2+ (E6-18) - Body ground
    VVT sensor (V4-2) or VV2- (E6-28) - Body ground

  1. Reconnect the VVT sensor connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR)


    BR03795E15
  1. Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4.CHECK CAMSHAFT (TOOTH)
  1. Remove the cylinder head cover .

  1. Check the tooth of the camshaft.

OK:
The camshaft does not have any cracks or deformation.



NG
REPLACE CAMSHAFT
OK

REPLACE ECM