Home › ENGINE ยท 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0604    Internal Control Module Random Access Memory (RAM) Error

DTC    P0606    ECM / PCM Processor

DTC    P0607    Control Module Performance

DTC    P0657    Actuator Supply Voltage Circuit / Open

for Preparation Click here


MONITOR DESCRIPTION

The ECM continuously monitors its internal memory status, internal circuits, and output signals sent to the throttle actuator. This self-check insures that the ECM is functioning properly. If any malfunction is detected, the ECM will set the appropriate DTC and illuminate the MIL.
The ECM memory status is diagnosed by internal "mirroring" of the main CPU and the sub CPU to detect Random Access Memory (RAM) errors. The 2 CPUs also perform continuous mutual monitoring. The ECM illuminates the MIL and sets a DTC if: 1) outputs from the 2 CPUs are different and deviate from the standards, 2) the signals sent to the throttle actuator deviate from the standards, 3) a malfunction is found in the throttle actuator supply voltage, and 4) any other ECM malfunction is found.

DTC No.
DTC Detection Condition
Trouble Area
P0604
P0606
P0607
P0657
ECM malfunction
ECM

MONITOR STRATEGY


Related DTCs
P0604: ECM RAM error
P0606: ECM CPU malfunction
P0607: ECM performance
P0657: ETCS power supply
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle: P0657
Continuous: P0604, P0606, P0607
Duration
Within 1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
None

TYPICAL MALFUNCTION THRESHOLDS


ECM RAM errors: 
RAM
RAM check failure

P0604: CPU malfunction 
Either of following conditions is met:
Condition 1 or 2
1. Difference between throttle position of main CPU and throttle position of sub CPU
0.3 V or more
2. Difference between accelerator pedal position of main CPU and accelerator pedal position of sub CPU
0.3 V or more

P0607: ECM range check 
Either of following conditions is met:
Condition 1 or 2
1. All of the following conditions is met
Conditions (a), (b) and (c)
(a). CPU reset
1 time or more
(b). Learned TP - Learned APP
0.4 V or higher
(c). Electronic throttle actuator
OFF
2. CPU reset
2 times or more

P0657: ETCS power supply 
ETCS power supply after ignition switch ON to OFF
7 V or more

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0604, P0606, P0607 or P0657)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0604, P0606, P0607 or P0657
    A
    P0604, P0606, P0607 or P0657 and other DTCs
    B

    HINT:
    If any DTCs other than P0604, P0606, P0607 and P0657 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A

REPLACE ECM