Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  2. Monitor the ECU data by following the prompts on the tester screen.

    HINT:
    The intelligent tester has a "Snapshot" function which records the monitored data. Refer to the intelligent tester operator's manual for further details.


DATA LIST

HINT:
Using the DATA LIST displayed on the intelligent tester, the value of the switch, sensor, actuator, etc. can be read without part removal. Reading the DATA LIST as the first step of troubleshooting is one way to shorten the labor time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Read the DATA LIST according to the display on the tester.

    BACK DOOR ECU: 
    Item
    Measurement Item/ Display (Range)
    Normal Condition
    Diagnostic Note
    WIPER RTRCT SW
    Rear wiper retract switch/ON or OFF
    ON: Rear wiper retract switch is in ON position
    OFF: Rear wiper retract switch is in OFF position
    -
    KEY SW (UNLK)
    Rear door lock key switch at UNLOCK position/ON or OFF
    ON: Rear door lock key switch at UNLOCK is in ON position
    OFF: Rear door lock key switch at UNLOCK is in OFF position
    -
    KEY SW (LOCK)
    Rear door lock key switch at LOCK position/ON or OFF
    ON: Rear door lock key switch at LOCK is in ON position
    OFF: Rear door lock key switch at LOCK is in OFF position
    -
    P/W POSITION
    Back door glass position/CLOSE or OPEN
    CLOSE: Back door glass is in CLOSE position
    OPEN: Back door glass is in OPEN position
    -
    GLASS POS-1/4
    Door glass position (Fully closed - 1/4 open) signal/OK or CAUTION
    OK: Power window is going UP by manual operation
    CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
    -
    GLASS POS-2/4
    Door glass position (1/4 open - 2/4 open) signal/OK or CAUTION
    OK: Power window is going UP by manual operation
    CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
    -
    GLASS POS-3/4
    Door glass position (2/4 open - 3/4 open) signal/OK or CAUTION
    OK: Power window is going UP by manual operation
    CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
    -

    BODY: 
    Item
    Measurement Item/ Display (Range)
    Normal Condition
    Diagnostic Note
    IG SW
    Engine switch signal/ ON or OFF
    ON: Power source mode is on (IG)
    OFF: Power source mode is off or on (ACC)
    -
    D DOR CTY SW
    Driver side door courtesy switch signal/ or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -
    P DOR CYT SW
    Front passenger side door courtesy switch signal/ ON or OFF
    ON: Front passenger side door is open
    OFF: Front passenger side door is closed
    -


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the intelligent tester allows you to operate the relay, VSV, actuator, etc. without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten the labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Perform the ACTIVE TEST according to the display on the tester.

    BACK DOOR ECU:

    Item
    Test Detail
    Diagnostic Note
    P/W UP/DOWN
    Operates back door power window UP/DOWN
    -