Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B065593E24

  1. Disconnect the I17 amplifier connector and measure the resistance between the terminal of the wire harness side connector and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (I17-7) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the I17 amplifier connector and measure the resistance and voltage of each terminal of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    VC5 (I17-1) - GND (I17-7)
    GR-B - L
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    CODE (I17-4) - GND (I17-7)
    P - L
    Demodulated signal of key code date
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    TXCT (I17-5) - GND (I17-7)
    LG-R - L
    Key code output signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    GND (I17-7) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, the amplifier may have a malfunction.



  3. Inspect using an oscilloscope.



      B055023
    1. Waveform 1 (Reference):
      Terminal
      CODE - GND
      Tool Setting
      10 V/DIV., 10 ms/DIV.
      Condition
      Key is in ignition key cylinder



    2. B055024
    3. Waveform 2 (Reference):
      Terminal
      TXCT - GND
      Tool Setting
      10 V/DIV., 10 ms/DIV.
      Condition
      Key is in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY

B111613E12

  1. Disconnect the T8 ECU connector and measure the resistance and voltage between each terminal of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (T8-1) - GND (T8-14)
    W-R - W-B
    Battery
    Always
    10 to 14 V
    IG (T8-2) - GND (T8-14)
    B-O - W-B
    Ignition switch
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    10 to 14 V
    KSW (T8-10) - GND (T8-14)
    G-Y - W-B
    Unlock warning switch
    No key is in ignition key cylinder
    10 kΩ or higher
    Key is in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the T8 ECU connector and measure the voltage of each terminal of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (T8-13) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    KSW (T8-10) - GND (T8-14)
    G-Y - W-B
    Unlock warning switch
    No key is in ignition key cylinder
    10 to 14 V
    Key is in ignition key cylinder
    Below 1 V
    VC5 (T8-8) - AGND (T8-13)
    GR-B - W
    Power source
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    4.6 to 5.4 V
    TXCT (T8-12) - AGND (T8-13)
    LG-R - W
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    CODE (T8-11) - AGND (T8-13)
    P-G - W
    Transponder key amplifier ground
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    EFIO (T8-6) - GND (T8-14)
    W-R - W-B
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 3
    EFII (T8-7) - GND (T8-14)
    L-R - W-B
    ECM input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 4
    If the result is not as specified, the ECU may have a malfunction.



  3. Inspect using an oscilloscope.



      B055023
    1. Wave form 1 (Reference):
      Terminal
      TXCT - AGND
      Tool Setting
      10 V/DIV., 10 ms/DIV.
      Condition
      Key is in ignition key cylinder



    2. B055024
    3. Wave form 2 (Reference):
      Terminal
      CODE - AGND
      Tool Setting
      10 V/DIV., 10 ms/DIV.
      Condition
      Key is in ignition key cylinder



    4. B052547
    5. Wave form 3 (Reference):
      Terminal
      EFIO - GND
      Tool Setting
      5 V/DIV., 5 ms/DIV.
      Condition
      Ignition switch ON



    6. B052548
    7. Wave form 4 (Reference):
      Terminal
      EFII - GND
      Tool Setting
      5 V/DIV., 5 ms/DIV.
      Condition
      Ignition switch ON


CHECK ECM

B050745E06

  1. Disconnect the E6 ECM connector and measure the resistance between the terminal of the wire harness side connector and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (E6-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E6 ECM. Measure the voltage between each terminal of the connector according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (E7-16) - E1 (E6-1)
    W-R - W-B
    Transponder key ECU input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 1
    IMO (E7-15) - E1 (E6-1)
    L-R - W-B
    Transponder key ECU output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Waveform 2
    If the result is not as specified, there may be a malfunction on the wire harness side.



  3. Inspect using an oscilloscope.



      B052547
    1. Waveform 1 (Reference):
      Terminal
      IMI - E1
      Tool Setting
      5 V/DIV., 5 ms/DIV.
      Condition
      Ignition switch ON



    2. B052548
    3. Waveform 2 (Reference):
      Terminal
      IMO - E1
      Tool Setting
      5 V/DIV., 5 ms/DIV.
      Condition
      Ignition switch ON