Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2796    No Communication in Immobiliser System

DTC    B2798    Communication Malfunction No. 2

for Preparation Click here


DESCRIPTION

These codes are stored in the memory when a key that does not have a transponder chip is inserted or if communication between the key and transponder key ECU is impossible.

DTC No.
DTC Detection Condition
Trouble Area
B2796
No communication
  1. Key
  2. Wire harness
  3. Transponder key amplifier
  4. Transponder key ECU assembly
B2798
Communication error
  1. Key
  2. Wire harness
  3. Transponder key amplifier
  4. Transponder key ECU assembly

WIRING DIAGRAM


B111588E16


INSPECTION PROCEDURE

1.READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester (with CAN VIM) to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select IMMOBILISER in the DATA LIST and read the value displayed on the intelligent tester.

    Transponder key ECU 
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    IMMOBILISER
    Immobiliser system status / SET or UNSET
    UNSET: Ignition switch on
    SET: Without key
    -

    OK:
    UNSET (Ignition switch on) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU ASSEMBLY
NG


2.CHECK KEYS
  1. Insert the vehicle's other key into the ignition key cylinder.

  1. Check that the engine starts with this key.

    OK:
    The engine starts.



OK
RE-REGISTER OR REPLACE KEY
NG


3.READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester (with CAN VIM) to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select ANTENNA COIL in the DATA LIST and read the value displayed on the intelligent tester.

    Transponder key ECU 
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    ANTENNA COIL
    Antenna coil condition /NORMAL or FAIL
    NORMAL: Antenna coil is normal.
    FAIL: Antenna coil is malfunctioning.
    -

    OK:
    NORMAL (Antenna coil is normal) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU ASSEMBLY
NG


4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY AMPLIFIER)


    B111591E13
  1. Disconnect the T8 ECU and I17 amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    T8-8 (VC5) - I17-1 (VC5)
    Below 1 Ω
    T8-11 (CODE) - I17-4 (CODE)
    T8-12 (TXCT) - I17-5 (TXCT)
    T8-13 (AGND) - I17-7 (GND)
    T8-8 (VC5) - Body ground
    10 kΩ or higher
    T8-11 (CODE) - Body ground
    T8-12 (TXCT) - Body ground
    T8-13 (AGND) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT TRANSPONDER KEY ECU ASSEMBLY


    B111616E17
  1. Reconnect the T8 ECU and I17 amplifier connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    T8-9 (VC5) - Body ground
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T8-13 (AGND) - Body ground
    Always
    Below 1 Ω



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK


6.CHECK TRANSPONDER KEY AMPLIFIER
  1. After replacing the transponder key amplifier with a normally functioning transponder key amplifier, check that the engine starts.

    OK:
    The engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END