Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1141/33    Side Airbag Sensor Assembly LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor assembly LH circuit consists of the safing sensor, the diagnostic circuit and the lateral deceleration sensor, etc.
If the center airbag sensor assembly receives signals from the lateral deceleration sensor, it judges whether or not the SRS should be activated.
DTC B1141/33 is recorded when a malfunction in the side airbag sensor assembly LH circuit is detected.

DTC No.
DTC Detecting Condition
Trouble Area
B1141/33
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side airbag sensor assembly RH circuit for 2 seconds.
  2. Side airbag sensor assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Side airbag sensor assembly LH
  2. Center airbag sensor assembly
  3. Floor wire No. 2

WIRING DIAGRAM


H043054E26


INSPECTION PROCEDURE

1.CHECK DTC


    C110453E02
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1141/33 is not output.

    HINT:
    Codes other than code B1141/33 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK 

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK FLOOR WIRE NO. 2 (OPEN)


    C110448E09
  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor assembly LH.

  1. Using a service wire, connect A30-16 (VUPL) and A30-18 (ESL) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUPL) - S16-1 (ESL)
    Always
    Below 1 Ω



    C110447E09
  1. Using a service wire, connect A30-17 (SSL+) and A30-20 (SSL-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    S16-3 (SSL+) - S16-2 (SSL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


4.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C109479E18
  1. Disconnect the service wire from connector "B".

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUPL) - Body ground
    Always
    Below 1 V
    S16-1 (ESL) - Body ground
    Always
    Below 1 V
    S16-3 (SSL+) - Body ground
    Always
    Below 1 V
    S16-2 (SSL-) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


5.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C109479E18
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUPL) - Body ground
    Always
    1 MΩ or higher
    S16-1 (ESL) - Body ground
    Always
    1 MΩ or higher
    S16-3 (SSL+) - Body ground
    Always
    1 MΩ or higher
    S16-2 (SSL-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


6.CHECK FLOOR WIRE NO. 2 (SHORT)


    C109479E18
  1. Measure the resistance according to the value(s) in the table below.

    Standard:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUPL) - S16-1 (ESL)
    Always
    1 MΩ or Higher
    S16-3 (SSL+) - S16-2 (SSL-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


7.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    C110452E02
  1. Connect the connector to the center airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Proceed To
    Display (DTC Output)
    NG: A
    DTC B1140/32 is output.
    NG: B
    DTC B1141/33 is output.
    OK
    DTC B1140/32 and B1141/33 are not output.



NG:A
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

NG:B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK