Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1152/28    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator light circuit consists of the center airbag sensor assembly and passenger airbag ON/OFF indicator. This circuit indicates the operation condition of the front passenger airbag assembly, the front seat airbag assembly RH and front seat belt pretensioner RH.
DTC B1152/28 is recorded when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1152/28
  1. The center airbag sensor assembly receives a line short signal, open signal, short to ground signal or B+ short signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.
  2. Passenger airbag ON/OFF indicator malfunction
  3. Center airbag sensor assembly malfunction
  1. Air conditioning control assembly (Passenger airbag ON/OFF indicator)
  2. Center airbag sensor assembly
  3. Instrument panel wire

WIRING DIAGRAM


H045967E01


INSPECTION PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the ignition switch to the ON position.



  1. Check the passenger airbag ON/OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).


    H043700E01


    Result:

    ON/OFF Indicator Illumination
    Proceed to
    Always ON
    A
    OFF
    B



B
Go to step 10
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the air conditioning control assembly.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the air conditioning control assembly.

  1. Check that the connectors (on the center airbag sensor assembly side and the air conditioning control assembly side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    H045951
  1. Connect the connector to the air conditioning control assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator ("ON" and "OFF") does not come on.



NG
Go to step 6
OK


5.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C110466E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1152/28 is not output.

    HINT:
    Codes other than code B1152/28 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK 

6.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C123759E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the air conditioning control assembly.

  1. Using a service wire, connect A32-1 (P-AB) and A32-25 (PAON) of connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - D3-13 (PAON)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C123760E01
  1. Disconnect the SST from connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - D3-13 (PAON)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C123760E01
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - Body ground
    Always
    1 MΩ or higher
    D3-13 (PAON) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C123760E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V
    D3-13 (PAON) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY 

10.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the air conditioning control assembly.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


11.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the air conditioning control assembly.

  1. Check that the connectors (on the center airbag sensor assembly side and the air conditioning control assembly side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


12.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C123759E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the telltale light assembly.

  1. Using a service wire, connect A32-1 (P-AB) and A32-25 (PAON) of connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - D3-13 (PAON)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


13.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C123760E01
  1. Disconnect the service wire from connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - D3-13 (PAON)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


14.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C123760E01
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - Body ground
    Always
    1 MΩ or higher
    D3-13 (PAON) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


15.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C123760E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    D3-6 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V
    D3-13 (PAON) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


16.CHECK AIR CONDITIONING CONTROL ASSEMBLY (POWER SOURCE)


    H045953E01
  1. Turn the ignition switch to the ON position.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Voltage and Resistance:
    Tester connection
    Condition
    Specified condition
    D3-2 (IG+) - Body ground
    Ignition switch ON
    10 to 14 V
    D3-7 (GND) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE WIRE HARNESS (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY) OR BATTERY
OK


17.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    H040065E24
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the telltale light assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Check the passenger airbag ON/OFF indicator condition.

    Result:
    Tester connection
    Condition
    Passenger airbag ON/OFF indicator condition
    A32-25 (PAON) - Body ground
    Ignition switch ON
    "ON" comes on
    A32-1 (P-AB) - Body ground
    Ignition switch ON
    "OFF" comes on



NG
REPLACE AIR CONDITIONING CONTROL ASSEMBLY
OK


18.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C110466E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1152/28 is not output.

    HINT:
    Codes other than code B1152/28 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK