Home › BODY › SEAT › POWER SEAT SWITCH

POWER SEAT SWITCH > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER SEAT SWITCH


    B105970E02
  1. Check the resistance between the terminals when each switch is operated.

    Standard resistance:
    Slide switch:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 9 (SLDF)
    FRONT
    Below 1 Ω
    4 (E) - 6 (SLDR)
    FRONT
    Below 1 Ω
    4 (E) - 6 (SLDR)
    OFF
    Below 1 Ω
    4 (E) - 9 (SLDF)
    OFF
    Below 1 Ω
    1 (B) - 6 (SLDR)
    REAR
    Below 1 Ω
    1 (E) - 6 (SLDF)
    REAR
    Below 1 Ω
    Front vertical switch:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 10 (FUP)
    UP
    Below 1 Ω
    4 (E) - 5 (FDWN)
    UP
    Below 1 Ω
    4 (E) - 5 (FDWN)
    OFF
    Below 1 Ω
    4 (E) - 10 (FUP)
    OFF
    Below 1 Ω
    1 (B) - 5 (FDWN)
    DOWN
    Below 1 Ω
    4 (E) - 10 (FUP)
    DOWN
    Below 1 Ω
    Rear vertical switch:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 7 (LUP)
    UP
    Below 1 Ω
    4 (E) - 8 (LDWN)
    UP
    Below 1 Ω
    4 (E) - 7 (LUP)
    OFF
    Below 1 Ω
    4 (E) - 8 (LDWN)
    OFF
    Below 1 Ω
    1 (B) - 8 (LDWN)
    DOWN
    Below 1 Ω
    4 (E) - 7 (LUP)
    DOWN
    Below 1 Ω
    Reclining switch:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 3 (RCLF)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    OFF
    Below 1 Ω
    3 (RCLF) - 4 (E)
    OFF
    Below 1 Ω
    1 (B) - 2 (RCLR)
    REAR
    Below 1 Ω
    3 (RCLF) - 4 (E)
    REAR
    Below 1 Ω

    If the result is not as specified, replace the switch.



2. INSPECT FRONT POWER SEAT SWITCH RH


    B111877E01
  1. Inspect the front passenger side power seat switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Slide switch:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 9 (SLDF)
      FRONT
      Below 1 Ω
      4 (B) - 6 (SLDR)
      FRONT
      Below 1 Ω
      4 (B) - 6 (SLDR)
      OFF
      Below 1 Ω
      4 (E) - 9 (SLDF)
      OFF
      Below 1 Ω
      1 (B) - 6 (SLDR)
      REAR
      Below 1 Ω
      4 (E) - 9 (SLDF)
      REAR
      Below 1 Ω
      Reclining switch:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (B) - 3 (RCLF)
      FRONT
      Below 1 Ω
      2 (RCLR) - 4 (E)
      FRONT
      Below 1 Ω
      2 (RCLR) - 4 (E)
      OFF
      Below 1 Ω
      3 (RCLF) - 4 (E)
      OFF
      Below 1 Ω
      1 (B) - 2 (RCLR)
      REAR
      Below 1 Ω
      3 (RCLF) - 4 (E)
      REAR
      Below 1 Ω

      If the result is not as specified, replace the switch.