Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2UZ-FE)

DTC    P0722    Output Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

G036793E03


DTC No.
DTC Detection Condition
Trouble Area
P0722
All conditions below are detected 500 times or more continuously (1-trip detection logic)
(a) No signal from speed sensor (SP2) is input to ECM while 4 pulses of No. 1 vehicle speed sensor signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
(c) Park/neutral position switch is OFF.
(d) Transfer position is except neutral (4WD).
  1. Open or short in speed sensor (SP2) circuit
  2. Speed sensor (SP2)
  3. ECM
  4. Automatic transmission assembly (clutch, brake or gear, etc.)

  1. Reference (Using an oscilloscope):
    Check the waveform between terminals SP2+ and SP2- of the ECM connector.
    G020664E11

    Standard:
    Refer to the illustration.

    Terminal
    SP2+ - SP2-
    Tool setting
    2 V/DIV., 20 ms./DIV
    Vehicle condition
    Vehicle speed 20 km/h (12 mph)

MONITOR DESCRIPTION

The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gearshift point and the lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.
If the ECM detects no signal from the output shaft speed sensor SP2 even while the vehicle is moving, it will conclude that is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0722 : Speed sensor SP2/Verify pulse input
Required Sensors/Components
Speed sensor SP2
Frequency of operation
Continuous
Duration
500 output shaft revolution
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
P0500 (VSS)
P0748 (Trans solenoid (range))
Vehicle speed sensor pulse input
4
Vehicle speed range (4 sec. or more)
9 km/h (5.59 mph) or more
NSW switch
OFF
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Output speed sensor pulse input
No input

WIRING DIAGRAM


G031763E49


INSPECTION PROCEDURE


DATA LIST

HINT:
According to the DATA LIST displayed by the intelligent tester, you can read the value of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of troubleshooting is one method to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "DIAGNOSIS / OBD/MOBD / ECT / DATA LIST".

  7. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item/Range (display)
    Normal Condition
    SPD (SP2)
    Output shaft Speed/min.: 0 km/h (0 mph) max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)

    HINT:
    Equal to vehicle speed

    HINT:
    1. SPD (SP2) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. The SPD (SP2) value displayed on the tester is much lower than the actual vehicle speed:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR INSTALLATION


    BR03795E43
  1. Check the speed sensor (SP2) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL SENSOR OR REPLACE SENSOR
OK


2.INSPECT SPEED SENSOR (SP2)


    C110343E41
  1. Disconnect the speed sensor connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (SP2)
OK


3.CHECK WIRE HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)


    G035616E79
  1. Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    E5-34 (SP2+) - E5-26 (SP2-)
    560 to 680 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    E5-34 (SP2+) - Body ground
    10 kΩ or higher
    E5-26 (SP2-) - Body ground
    ↑



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM