Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › OIL PUMP

OIL PUMP > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT OIL PUMP BODY O-RING


    D027950E01
  1. Remove the O-ring from the oil pump assembly.



2. FIX OIL PUMP ASSEMBLY


    D027951E04
  1. Place the oil pump body on the torque converter clutch.



3. REMOVE CLUTCH DRUM OIL SEAL RING


    D027952E05
  1. Remove the 3 oil seal rings.



4. REMOVE STATOR SHAFT ASSEMBLY


    D027953E01
  1. Remove the 14 bolts, and then remove the stator shaft from the oil pump body.



5. REMOVE FRONT OIL PUMP BODY O-RING


    D027963E01
  1. Remove the O-ring from the oil pump body.

  1. Remove the oil pump body from the torque converter clutch.



6. INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY


    D027954E01
  1. Using a dial indicator, measure the inside diameter of the oil pump body bushing.

    Maximum inside diameter:
    38.188 mm (1.5035 in.)

    1. If the inside diameter is greater than the maximum, replace the oil pump body.



7. INSPECT STATOR SHAFT ASSEMBLY


    D027955E01
  1. Using a dial indicator, measure the inside diameter of the stator shaft bushing.

    Maximum inside diameter:
    Front side:
    21.577 mm (0.8495 in.)
    Rear side:
    32.08 mm (1.2629 in.)

    1. If the inside diameter is grater than the maximum, replace the stator shaft.



8. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY


    D027956E01
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.0039 to 0.0067 in.)

    Maximum body clearance:
    0.17 mm (0.0067 in.)

    1. If the body clearance is greater than the maximum, replace the drive gear, driven gear or pump body.



    D027957E01
  1. Using a feeler gauge, measure the clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.070 to 0.150 mm (0.0028 to 0.0059 in.)

    Maximum tip clearance:
    0.150 mm (0.0059 in.)

    1. If the tip clearance is greater than the maximum, replace the drive gear, driven gear or pump body.



    D001286E01
  1. Using a steel straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.002 in.)

    Maximum side clearance:
    0.05 mm (0.002 in.)

    If the side clearance of both is gears greater than the maximum, replace the drive gear, driven gear or pump body.

  1. There are 5 different thicknesses for the drive and driven gears.

    Standard drive and drive gears thickness:
    Mark
    Thickness
    0
    10.74 to 10.749 mm (0.4228 to 0.4232 in.)
    1
    10.75 to 10.759 mm (0.4232 to 0.4236 in.)
    2
    10.76 to 10.77 mm (0.4236 to 0.4240 in.)
    3
    10.771 to 10.78 mm (0.4241 to 0.4244 in.)
    4
    10.781 to 10.79 mm (0.4244 to 0.4248 in.)

    1. If the side clearance is greater than the maximum, replace the drive gear, driven gear or pump body.



9. REMOVE FRONT OIL PUMP DRIVE GEAR


D027958E01


10. REMOVE FRONT OIL PUMP DRIVEN GEAR


D027959E01


11. REMOVE FRONT OIL PUMP OIL SEAL


    D027960E01
  1. Using a screwdriver, remove the oil seal.

    NOTICE:
    Be careful not to damage the bushing and oil pump body.